millennia td-1 Manual Do Utilizador

TD-1

36

Instrument / DI Input Amplifier Topology

TUBE:  Selected dual triode vacuum tube (250V)
SOLID STATE:  All discrete J-FET amplifier (50V)

THD + Noise, 20 Hz - 30 kHz (35 dB Gain)

0.0005% typical mic / line,  0.03% typical vacuum tube

Intermodulation Distortion

0.0009% typical mic / line, 0.03% typical vacuum tube

Frequency Response @ -3 dB points

3 Hz to 300 kHz, typical.  Varies with path & topology

Frequency Response @ -0.5 dB points

7 Hz to 100 kHz, typical.  Varies with path & topology

Frequency Response, DIT-01 Transformer

Better than 3 Hz to 300 kHz (+/- 3.0 dB)

Frequency Response, DI - Tube Path

-1.0 dB, better than 10 Hz to 40 kHz

Frequency Response, DI - SS Path

-1.0 dB, better than 5 Hz to 100 kHz

Maximum Balanced Mic Input Level

+23 dBu (Pad not engaged)

Maximum Balanced Line Input Level

+23 dBu (+43 dBu Pad engaged, or >100 Volts RMS)

Maximum DI Input Level (Tube & SS)

+18 dBu (+26 dBu Pad engaged, or >15 Volts RMS)

Maximum Output Level

+32 dBu active balanced outputs, +26 dBu unbal outputs

Maximum System Gain

45 dB standard (65 dB with optional HV-3 mic preamp*)

Input Impedance (mic)

6,200 ohms, nominal with phantom power engaged

Input Impedance (line)

6,900 ohms, pad out.

Input Impedance (DI - Tube & SS)

switchable:   470K ohms / 2M ohms / 10M ohms

Output Impedance

24.3 (x2) ohms balanced. 49.9 ohms unbalanced

Noise (Mic)

   (EQ out, 60 dB gain)

-128 dB EIN, 150 ohm source

Noise (Line)  (EQ in, 10 dB gain)

-105 dBu

Noise (DI)      (EQ in, 10 dB gain)

-90 dBu

Common Mode Rejection Ratio, mic in

> 60 dB typical, 100 mV CM (10 Hz - 100 kHz)
> 80 dB typical @ 60 & 120 Hz, 100 mV CM

Phase Error (EQ out)

Less than +/- 5 degrees 50 Hz to 20 kHz, typical

Three-pin XLR Polarity

Pin 2 = positive polarity, Pin 1 = ground

¼” Phone Polarity (unbal)

Sleeve = ground, Tip = positive polarity

¼” Phone Polarity (balanced)

Sleeve = ground, Tip = pos pol, Ring = neg pol

Maximum Boost & Cut

+/- 15 dB (21 step detent)

Parametric “Q” Adjustment Range

Q = 0.4 to 4.0, sweepable

Low Freq (LF) Parametric Sweep Freqs

20 Hz to 220 Hz -or-  200 Hz to 2.2 kHz (sw selectable)

High Freq (HF) Parametric Sweep Freqs

250 Hz to 2.5 kHz -or-  2.5 kHz to 25 kHz (sw selectable)

Bypass Selection on Each E.Q. Band?

Yes

E.Q.  IN / OUT Switch?

Yes

E.Q. Topology

Solid State

Power Consumption

35 Watts, nominal

Power Requirements

100 VAC to 240 VAC, 50/60 Hz, selectable

Fuses (2 required) 100-120VAC Mains

2 ea 1.0 A (5x20mm, U.S. slow-blow, 250V)

              200-240VAC Mains

2 ea 500 mA (5x20mm, U.S. slow-blow, 250V)

Internal DC Power

+250V, +48V, +25V,  -25V, +18V, -18V, +12.6V, +5V

Dimensions

approximately 8.5" W x 13" D x 3.5" H

Net Weight

approximately 15 pounds

 * Maximum HV-3 preamplifier gain can be factory modified up to 85 dB upon customer request.
     Millennia Media reserves the right to change specification and delivery without notice.