Panasonic NVVP60SERIES Guia De Utilização
RQTV0114
12
Tuning the TV to Your Unit
The unit supplies a signal to the TV via the RF coaxial cable on
channel AU28
channel AU28
s69 or NZ21s69. It is possible to view the unit’s
picture on your TV in the same way that you watch TV broadcasts.
The unit is fitted with its own tuner (just like a normal TV) and can be
preset to receive up to 99 TV broadcast stations.
≥Press [VHS SELECT] (
The unit is fitted with its own tuner (just like a normal TV) and can be
preset to receive up to 99 TV broadcast stations.
≥Press [VHS SELECT] (
l 8).
¬ If you have connected the unit to the TV through the audio/
video output sockets
You do not need to follow the procedure below. To view the pictures
from the unit, set to the AV mode on the TV with [AV].
from the unit, set to the AV mode on the TV with [AV].
The local TV broadcast channels 2, 7, 9, 10 and 28 are factory-
preset in the unit.
This means that if you can receive TV broadcasts on VHF channels
2, 7, 9, 10 and UHF channel 28, these are already tuned on the
programme positions with the matching numbers.
preset in the unit.
This means that if you can receive TV broadcasts on VHF channels
2, 7, 9, 10 and UHF channel 28, these are already tuned on the
programme positions with the matching numbers.
.........................................................................................................................................................................................................................
[1]
Press [
ÍVHS] to turn on
this unit.
.................................................................................................................................
[2]
Hold down [MENU] for 5
seconds or more.
seconds or more.
.................................................................................................................................
[3]
Set the TV to an unused
position for the unit viewing
channel.
position for the unit viewing
channel.
≥Tune the TV until the display shown on the above appears.
Refer also to the TV’s instructions regarding tuning.
.........................................................................................................................................................................................................................
[4]
Press [MENU].
When the unit is turned on after
connecting the aerial cable and the
mains lead for the first time, tuning
starts automatically.
≥If the unit is turned on with the aerial not
connecting the aerial cable and the
mains lead for the first time, tuning
starts automatically.
≥If the unit is turned on with the aerial not
connected, all channels are skipped.
.................................................................................................................................
[1]
Press [
ÍVHS] to turn on
this unit.
.................................................................................................................................
[2]
Set the TV to an unused
position for the unit
viewing channel.
position for the unit
viewing channel.
.................................................................................................................................
[3]
Press [MENU].
ª To cancel Auto Tuning halfway through
Auto Tuning will stop halfway if the unit is turned off, [MENU] is
pressed, playback starts or there is a power failure.
pressed, playback starts or there is a power failure.
¬ If Auto Tuning stops halfway by turning the unit off, playback
or power failure
≥Disconnect the mains lead and then reconnect it.
≥Turn on the unit. Plug in Auto Tuning restarts.
≥Turn on the unit. Plug in Auto Tuning restarts.
¬ To set the channels manually (
l 20)
ª To restart Plug in Auto Tuning
≥Turn the unit on.
≥Make sure there is no video cassette in the
≥Make sure there is no video cassette in the
unit.
1) Keep
both
[
ICH]
and [
JCH] on the
unit pressed simultaneously for 3
seconds or more until the channel on
the unit’s display changes to 1.
seconds or more until the channel on
the unit’s display changes to 1.
2) Disconnect the mains lead and then reconnect it.
3) Turn on the unit. Plug in Auto Tuning restarts.
3) Turn on the unit. Plug in Auto Tuning restarts.
You can change the RF output channel, for
example, when interference occurs on the
picture after tuning.
example, when interference occurs on the
picture after tuning.
.................................................................................................................................
[1] Press [MENU] for 5
seconds or more.
.................................................................................................................................
[2] Press [
JCH] or [ICH
]
to
select the channel
(AU28
(AU28
s69, NZ21s69).
≥Each time you press [
JCH]
or
[
ICH], (l below).
≥Set to “ss” (RF OFF) when you use
the audio/video cable for the
connection.
connection.
≥You can also use the numeric buttons.
Example: “28”; [2]
l[8]
.............................................................................................
[3] Retune your TV to
the new RF channel
for the unit.
for the unit.
.............................................................................................
[4] Press [MENU] to exit
the setting mode.
Note:
≥Even if the RF output channel has been changed, it is not
≥Even if the RF output channel has been changed, it is not
necessary to perform Auto Tuning.
Pre-programmed TV Channels (for NV-VP60GL/
Australia)
Australia)
Plug in Auto Tuning (for NV-VP60GN/New Zealand)
Disappears
1
To Change the RF Output Channel
NV-VP60GL
NV-VP60GN
28
…
69
(RF OFF)
NV-VP60GL
21
69
(RF OFF)
NV-VP60GN
VP60GL.book Page 12 Monday, March 6, 2006 2:49 PM