Robust DataComm rdc485ir3-dv-3p-cc Repeater Guia De Especificação
Isolated RS-485 Repeater (2-wire)
Dimensions in mm (and inches)
Specification
Order Information
: at least 115Kbps over 500m
: transparent, no configuration required
: Each receive signal has LED (yellow)
: 1000m for EIA/RS-485
: less than 3000m for RS-485
(requires quality, low-cap cable < 50 pf/m)
: transparent, no configuration required
: Each receive signal has LED (yellow)
: 1000m for EIA/RS-485
: less than 3000m for RS-485
(requires quality, low-cap cable < 50 pf/m)
: EIA/RS-485A
: -7 to +12 vDC
: +/- 25 vDC
: -7 to +12 vDC
: +/- 25 vDC
Mechanical / Environment
Communication:
Power Supply:
Isolation
(Version 1.1) Specifications subject to change without notice.
LEDs (green) indicate isolated power status
25 (1.0)
79 (3.1)
85.5 (
3
.4)
90.5 (
3
.6)
93.0 (
3
.7)
EN 50 022 - 7.5mm
EN 50 035
EN 50 022 - 15mm
EN 50 035
EN 50 022 - 15mm
93 (3.7)
Block Diagram
Gnd-B
LED
V+
V--
V--
Main
Supply
Supply
LED
(ISO/IEC 9549)
screw terminals
Isolated
Supply
D+A
D--A
LED
Gnd-A
LED
screw terminals
-
Installed
FI
Not installed
Fault Isolation Option for Port A
5v
2p
3p
Galvanic Isolation Configuration
Power Supply Configuration
Boxes in bold denote factory default options
D+B
D--B
D--B
Model: rdc485ir3
5v +/- 5% Regulated DC Supply
9 to 36v Unregulated DC Supply
rdc485ir3
-
-
Fie
ld
RS
-4
85
(Po
rt A
)
Lo
cal
RS-
cal
RS-
4
8
5
(
P
o
rt B
)
D+A
D-A
Gnd-A
dd
dv
3-port, isolation between ports A, B & supply
2-port, Gnd-B = Supply Ground (5v supply only)
-
Option 3p includes 500 watt transient surge suppressor diodes
on both RS-485 ports. Option 2p has them only on port A.
on both RS-485 ports. Option 2p has them only on port A.
Signal Type ................
Voltage Level ............
Permitted Surge .......
Voltage Level ............
Permitted Surge .......
Port A to Port B .........
Supply to Port A .......
Supply to Port B ........
Conformal Coating ..
Supply to Port A .......
Supply to Port B ........
Conformal Coating ..
: 2500 v (optical, 5kV test)
: 2500 v (galvanic, 3kV test)
: 2-port = none ; 3-port = 2500v
: 14,000 v per mm
: 2500 v (galvanic, 3kV test)
: 2-port = none ; 3-port = 2500v
: 14,000 v per mm
: -20C to +65C
: -40C to +100C
: 10 to 90% RH, non-condensing
: wire up to 2.5mm (12 AWG)
: nylon polymide, fungus and termite resistant
self-extinguishing, epoxy potting
: approx 130g
: DIN EN 50 022 or DIN EN 50 035
: -40C to +100C
: 10 to 90% RH, non-condensing
: wire up to 2.5mm (12 AWG)
: nylon polymide, fungus and termite resistant
self-extinguishing, epoxy potting
: approx 130g
: DIN EN 50 022 or DIN EN 50 035
Operating Range .......
Storage Range ............
Relative Humidity.......
Terminals .....................
Case Material .............
Storage Range ............
Relative Humidity.......
Terminals .....................
Case Material .............
Weight .........................
Mounting Rail .............
Mounting Rail .............
Max Speed .................
Character Setting .....
User Indications ........
Standard Distance ...
Practical Distance .....
Character Setting .....
User Indications ........
Standard Distance ...
Practical Distance .....
Copyright © 1996 Robust DataComm Pte Ltd
The rdc485ir3 safely connects 2-wire RS-485
devices and networks together without danger of
ground loops and damaging surges. It also dou-
bles permitted cable length. The isolated DC
supplies provide full 3-port galvanic isolation up
to 2.5 KV, which also implies that the grounds of
the data ports are floating with respect to each
other as well as the supply port. Data direction
control is fully automatic. The internal terminating
resistor (120 ohms) and bias resistors can be
enabled via jumpers. 500 watt voltage transient
suppressor diodes protect the rdc485ir3 from
normal mode surges, while the full galvanic
isolation protects the rdc485ir3 from common
mode surges. With the "Fault Isolation" (
devices and networks together without danger of
ground loops and damaging surges. It also dou-
bles permitted cable length. The isolated DC
supplies provide full 3-port galvanic isolation up
to 2.5 KV, which also implies that the grounds of
the data ports are floating with respect to each
other as well as the supply port. Data direction
control is fully automatic. The internal terminating
resistor (120 ohms) and bias resistors can be
enabled via jumpers. 500 watt voltage transient
suppressor diodes protect the rdc485ir3 from
normal mode surges, while the full galvanic
isolation protects the rdc485ir3 from common
mode surges. With the "Fault Isolation" (
FI
)
option, line breaks and/or shorts on Port A's
segment will not interfere with the data on Port
B's segment.
Isolation, industrial design, small size, DIN rail
mount, user indication, and DC supply make the
rdc485ir a very engineer-friendly device for your
industrial data communication system.
segment will not interfere with the data on Port
B's segment.
Isolation, industrial design, small size, DIN rail
mount, user indication, and DC supply make the
rdc485ir a very engineer-friendly device for your
industrial data communication system.
3-pin Removable Compression Terminal Blocks
Co. & GST Reg. No: 19-9600 372-Z
D-sub 9-pin for both ports (1 x male, 1 x female)
Removable screw terminal for both ports
cc
www.robustdc.com
Connector Configuration
: 1.2 watt (About 50 mA @ 24 Vdc)
: About 175 mA
: About 175 mA
9 to 36v DC................
5v DC +/- 10%...........
5v DC +/- 10%...........
RS-485 Ports
Fault Isolation
Master
rdc485i
r3
Slave 1
Slave 2
rdc485i
r3
Slave 3
Slave 4
Fault Isolated Segments
When a line fault (short or
open-circuit) occurs at any
one of the segments, the
other segments will not be
affected.
For example, when a line
short occurs between slaves
3 and 4, the Master will still
be able to poll slaves 1 and 2
normally.
open-circuit) occurs at any
one of the segments, the
other segments will not be
affected.
For example, when a line
short occurs between slaves
3 and 4, the Master will still
be able to poll slaves 1 and 2
normally.
Port B
Port A
Port B
Port A
-
with conformal coating
without conformal coating
Conformal Coating Option
cf
Making Industrial Data Flow Like Water ... Safely, Silently, & Sanely
Robust DataComm Pte Ltd (USA) 26471 Portola Pkwy #1E-242, Foothill Ranch CA 92610-1743, +1,972-248-7466
(International) 18 Kaki Bukit Road 3 #02-08 Entrepreneur Business Centre Singapore 415978, +65,6487-5624
(International) 18 Kaki Bukit Road 3 #02-08 Entrepreneur Business Centre Singapore 415978, +65,6487-5624