Pioneer Stage 4 DEX-P99RS Manual Do Proprietário
4
Push MULTI-CONTROL left or right to
select the cut-off frequency (crossover fre-
quency) of the selected speaker unit (fil-
ter).
Each time
quency) of the selected speaker unit (fil-
ter).
Each time
MULTI-CONTROL is pushed left or
right, cut off frequencies (crossover frequen
cies) are selected in the following order:
cies) are selected in the following order:
! High-LPF
5k
6.3k
8k
10k
12.5k
16k
20k
! High-HPF
800Hz
1k
1.25k
1.6k
2k
2.5k
3.15k
4k
5k
6.3k
8k
10k
12.5k
16k
! Mid-LPF, Low-LPF and SW-LPF
25Hz
31.5Hz
40Hz
50Hz
63Hz
80Hz
100Hz
125Hz
160Hz
200Hz
250Hz
315Hz
400Hz
500Hz
630Hz
800Hz
1k
1.25k
1.6k
2k
2.5k
3.15k
4k
5k
6.3k
8k
10k
12.5k
16k
20k
! Mid-HPF, Low-HPF and SW-HPF
20Hz
25Hz
31.5Hz
40Hz
50Hz
63Hz
80Hz
100Hz
125Hz
160Hz
200Hz
250Hz
315Hz
400Hz
500Hz
630Hz
800Hz
1k
1.25k
1.6k
2k
2.5k
3.15k
4k
5k
6.3k
8k
10k
12.5k
16k
# You cannot select speakers that are set to off
in the initial setting. Refer to Setting the speakers
on page 35.
in the initial setting. Refer to Setting the speakers
on page 35.
5
Push MULTI-CONTROL up or down to
adjust the level of the selected speaker
unit (filter).
Each time
unit (filter).
Each time
MULTI-CONTROL is pushed up or
down, the level of the selected speaker unit (fil
ter) increases or decreases.
0 dB to
ter) increases or decreases.
0 dB to
–24 dB is displayed as the level is in
creased or decreased if you have selected
High-LPF, High-HPF, Mid-LPF or Mid-HPF.
6 dB to
High-LPF, High-HPF, Mid-LPF or Mid-HPF.
6 dB to
–24 dB is displayed as the level is in
creased or decreased, only if you have se
lected
lected
Low-LPF, Low-HPF, SW-LPF or
SW-HPF.
6
Turn MULTI-CONTROL to select NW 3 in
the audio function menu.
Refer to Introduction of audio adjustments on
page 24.
Refer to Introduction of audio adjustments on
page 24.
7
Push MULTI-CONTROL left or right to
select the slope of the selected speaker
unit (filter).
Each time
unit (filter).
Each time
MULTI-CONTROL is pushed left or
right, slopes are selected in the following
order:
order:
! High-HPF
6dB/oct.
12dB/oct.
18dB/oct.
24dB/oct.
30dB/oct.
36dB/oct.
! High-LPF, Mid-LPF, Mid-HPF, Low-LPF,
Low-HPF, SW-LPF and SW-HPF
Pass
Pass
6dB/oct.
12dB/oct.
18dB/oct.
24dB/oct.
30dB/oct.
36dB/oct.
8
Push MULTI-CONTROL up or down to
switch the phase of the selected speaker
unit (filter).
Push
unit (filter).
Push
MULTI-CONTROL up selects normal
phase and
NOR appears in the display. Push
MULTI-CONTROL down selects reverse phase
and
and
REV appears in the display.
# You can adjust the parameters for other
speaker units (filters) in the same way.
speaker units (filters) in the same way.
9
Press B to cancel the network adjust-
ment mode.
Using the time alignment
The time alignment lets you adjust the dis
tance between each speaker and the listening
position.
tance between each speaker and the listening
position.
1
Use MULTI-CONTROL to select TA1 in
the audio function menu.
Refer to Introduction of audio adjustments on
page 24.
Refer to Introduction of audio adjustments on
page 24.
Audio Adjustments
En
28
Section
03