Kenwood KMR-M322BT Manual Do Proprietário
ENGLISH
35
INSTALLATION/CONNECTION
Warning
• The unit can only be used with a 12 V DC power supply, negative ground.
• Disconnect the battery’s negative terminal before wiring and mounting.
• Do not connect Battery wire (yellow) and Ignition wire (red) to the car chassis or Ground wire
• Disconnect the battery’s negative terminal before wiring and mounting.
• Do not connect Battery wire (yellow) and Ignition wire (red) to the car chassis or Ground wire
(black) to prevent a short circuit.
• To prevent short circuit:
– Insulate unconnected wires with vinyl tape.
– Be sure to ground this unit to the car’s chassis again after installation.
– Secure the wires with cable clamps and wrap vinyl tape around the wires that come into
contact with metal parts to protect the wires.
Caution
• For safety’s sake, leave wiring and mounting to professionals. Consult the car audio dealer.
• Install this unit in the console of your vehicle. Do not touch the metal parts of this unit during
• Install this unit in the console of your vehicle. Do not touch the metal parts of this unit during
and shortly after use of the unit. Metal parts such as the heat sink and enclosure become hot.
• Do not connect the
[ wires of speakers to the car chassis or Ground wire (black), or connect
them in parallel.
• Mount the unit at an angle of less than 30º.
• If your vehicle wiring harness does not have the ignition terminal, connect Ignition wire (red)
• If your vehicle wiring harness does not have the ignition terminal, connect Ignition wire (red)
to the terminal on the vehicle’s fuse box which provides 12 V DC power supply and is turned
on and off by the ignition key.
on and off by the ignition key.
• Keep all cables away from heat dissipate metal parts.
• After the unit is installed, check whether the brake lamps, blinkers, wipers, etc. on the car are
• After the unit is installed, check whether the brake lamps, blinkers, wipers, etc. on the car are
working properly.
• If the fuse blows, first make sure the wires are not touching car’s chassis, then replace the old
fuse with one that has the same rating.
Basic procedure
1 Remove the key from the ignition switch, then disconnect the
[ terminal of the car
battery.
2 Connect the wires properly.
See Wiring connection. ( 37)
3 Install the unit to your car.
See Installing the unit (in-dash mounting). ( 36)
4 Connect the
[ terminal of the car battery.
5 Press
to turn on the power.
6 Detach the faceplate and reset the unit within 5 seconds. ( 3)
REFERENCES
Source name
/
Display information
STANDBY
Source name Clock (back to the beginning)
RADIO
Frequency
Clock (back to the beginning)
(For FM Radio Broadcast Data System only)
Station name Radio text Radio text+ Title/Artist
Frequency Clock (back to the beginning)
Station name Radio text Radio text+ Title/Artist
Frequency Clock (back to the beginning)
USB
(For MP3/WMA/AAC/WAV/FLAC files)
Song title/Artist Album title/Artist Folder name File name
Song title/Artist Album title/Artist Folder name File name
Playing time Clock (back to the beginning)
iPod USB/iPod BT or
ANDROID
ANDROID
When [MODE OFF]/[BROWSE MODE] is selected ( 10):
Song title/Artist Album title/Artist Playing time Clock
(back to the beginning)
Song title/Artist Album title/Artist Playing time Clock
(back to the beginning)
PANDORA/PANDORA BT
Station name Shared/Radio station Song title Artist
Album title Playing time Clock (back to the beginning)
Album title Playing time Clock (back to the beginning)
IHEARTRADIO
Station name Song title/Artist Clock
(back to the beginning)
(back to the beginning)
SPOTIFY/SPOTIFY BT
Context title Song title Artist name Album name
Playing time Clock (back to the beginning)
Playing time Clock (back to the beginning)
BT AUDIO
Song title/Artist Album title/Artist Playing time Clock
(back to the beginning)
(back to the beginning)
AUX
Source name Clock (back to the beginning)
JS_KWD_KMM_BT522HD_KN_EN_9.indd 35
7/7/2017 11:25:01 AM