Elexa Consumer Products Inc. DMDP1 Manual Do Utilizador
Thank you for purchasing the DOME
Door/Window Sensor Pro! Use this device with
your Z-Wave Certified Controller to monitor
doors, windows, and other openings in your
home and also to monitor ambient temperature
levels.
Including/Connecting into the Z-Wave Network:
(Door/Window Sensor Pro not yet powered on)
Follow the instructions for your Z-Wave certified Controller to
enter inclusion mode. When prompted by the Controller:
1. For proper inclusion, bring the Door/Window Sensor Pro to
1. For proper inclusion, bring the Door/Window Sensor Pro to
where it will be used.*
2. Remove the Battery Tab.
The LED Indicator will alternate between green and red, then flash
The LED Indicator will alternate between green and red, then flash
green three times indicating inclusion.
Including/Connecting into the Z-Wave Network:
Including/Connecting into the Z-Wave Network:
(Door/Window Sensor Pro already powered on)
Follow the instructions for your Z-Wave certified Controller to
enter inclusion mode. When prompted by the Controller:
1. For proper inclusion, bring the Door/Window Sensor Pro to
1. For proper inclusion, bring the Door/Window Sensor Pro to
where it will be used.*
2. Open the Sensor Cover.
3. Press the Connect/Tamper Button three times and the LED
3. Press the Connect/Tamper Button three times and the LED
Indicator will alternatingly flash green and red until inclusion.
The LED Indicator will alternate between green and red, then flash
green three times indicating inclusion.
Key Features
• Z-Wave Plus Certified
• S0 Security-Enabled*
• Built-In Temperature Sensor (off by default)
• Up to 260’ range
• Ten-Year Battery Life
• LED Signal Strength Indication
• 1” Max distance between sensor & magnet
• Ultra-Narrow (1/4”) Magnet for Placement
• S0 Security-Enabled*
• Built-In Temperature Sensor (off by default)
• Up to 260’ range
• Ten-Year Battery Life
• LED Signal Strength Indication
• 1” Max distance between sensor & magnet
• Ultra-Narrow (1/4”) Magnet for Placement
Between Door and Casing
• Monitor doors, windows, medicine cabinets,
• Monitor doors, windows, medicine cabinets,
drawers, garage doors, and many other openings
*For non Z-Wave Plus networks, please consult the owner’s manual for your
primary controller to determine the best method and location for adding the
Door/Window Sensor Pro to your Z-Wave network.
*Encrypted communication requires S0-capable controllers.
Excluding/Disconnecting from the Z-Wave Network:
Follow the instructions for your Z-Wave certified Controller to
enter exclusion mode. When prompted by the Controller:
1. Remove the Cover of the Door/Window Sensor Pro.
2. Press the Connect/Tamper Button quickly 3 times in a row.
The LED Indicator will flash three times indicating exclusion/dis-
2. Press the Connect/Tamper Button quickly 3 times in a row.
The LED Indicator will flash three times indicating exclusion/dis-
connection, then start blinking yellow (red + green.)
Resetting the Door/Window Sensor Pro to Factory
Default Settings:
To disconnect from the Z-Wave Network and restore factory default
settings:
1. Open the Cover and make sure the Door/Window Sensor Pro
is powered.
2. Wait 5 seconds.
3. Move the magnet in and our of the closed position 6 times.
4. The LED Indicator will light red for 2 seconds indicating suc-
3. Move the magnet in and our of the closed position 6 times.
4. The LED Indicator will light red for 2 seconds indicating suc-
cessful reset, then start blinking yellow (red + green.)
Only do this if the controller is disconnected or otherwise unreachable!
Door/Window Sensor Pro
DMDP1
SOLIDWORKS Educational Product. For Instructional Use Only.
Screw Holes
LED Indicator
Connect/Tamper Button
Sensor Cover Release Button
Reed Switch
Figure 1 - Main Parts of the Door/Window Sensor Pro