Wireless Environment LLC MBN391 Manual Do Utilizador

Motion/Light Sensor: Light instantly turns on when it detects motion from 

up to 25 feet away. The light sensor conserves battery life by preventing the 

light from activating in daylight.

Auto Shut-off: Light shuts off automatically after 20 

seconds if no motion is detected.

Fully Adjustable: Light can be rotated 360° as well as 170° up and down.

Bright LEDs: 450 lumens cover up to 675 sq. ft.

Durable, Weather Resistant: Tight seals and UV resistant material allow 

the light to work in all weather conditions.

Networking: Spotlights will activate simultaneously when any spotlight 

within the network detects motion. They will deactivate simultaneously if no 

motion is detected in the group.

Installation Instructions

NetBright

®

 UltraBright Spotlight

• 1 Small Screwdriver

• 4 D-Cell Alkaline Batteries

• 1 Wireless Spotlight

• 3 Screws

• 3 Anchors

LED Lights

Mounting Base

Mounting Base 

Thumb Screw

Knuckle Screw

Motion & 

Light Sensor

for purchasing the Mr Beams

®

 

NetBright

®

 UltraBright Spotlight. We are 

committed to eliminating darkness using the latest 

in Light-Emitting Diodes (LEDs). LEDs are the most 

efficient and durable light sources available. We 

are certain that your light will contribute to a safer 

environment and provide light where you need it at 

a very reasonable cost.

www.mrbeams.com

1. Remove front cover of spotlight 

by rotating counterclockwise as 

shown above. Pull face out from 

cup to reveal battery holder.

2. Separate two parts by squeezing 

tabs and pulling apart.

4. Remove mounting base by turning thumb 

screw counterclockwise. Pull mounting base 

off stem of light.

5. Drive three screws into three holes to 

mount the mounting base. For drywall, drill 

pilot holes first and insert anchors.

6. Insert spotlight back into mounting base 

positioned in the desired direction. Tighten 

mounting base thumb screw.

7. To pivot spotlight up and down, loosen 

knuckle screw in the joint of the Spotlight 

stem and adjust Spotlight head to desired 

direction. Tighten knuckle screw.

3. Insert 4 D-Cell batteries into 

spotlight. Attach holder by aligning 

the grooves on the side and match 

white arrows, snapping both tabs in 

the holder.

• 

Use only new alkaline D-Cell batteries with 1.5V rating. 

• 

Do not mix old and new batteries. If batteries are not new, it may cause the light to malfunction. 

• 

Install batteries with polarity in correct position. 

• 

Light may activate when batteries are inserted. Simply take light into a dark room, allow 

   batteries to settle up to ten minutes, then test activation.

• 

If your light will not turn off, it means that it is time to replace the batteries. 

Battery Caution: 

1) Do not mix old and new batteries

2) Do not mix Alkaline, Standard (Carbon-Zinc) or Rechargeable (Nickel Cadmium) 

    or (Nickel Metal Hydride) batteries

3) Do not dispose of batteries in fire

4) Batteries should be recycled or disposed of as per state and local guidelines

600 Beta Drive, Mayfield Village, Unit 100, Mayfield, OH 44143

877.298.9082

After inserting the batteries, choose a group or channel 

for your spotlights with the dipswitches next to the battery 

compartment. Ensure all units are on the same channel by 

matching the dipswitch positions.

* Spotlights set to the same group will activate together when they 

are within 150 ft of each other.

Tips: 

1. You may need to rotate the battery compartment to reveal the dipswitches.

2. Use a pencil or a small screwdriver to adjust the switch positions.