Visonic Ltd. ZBT Manual Do Utilizador

D-303360 CLIP SMA Installer's Guide 

1 

 

 

The CLIP SMA is the smallest and most elegant wireless curtain-

pattern PIR detector for indoor use and designed for easy 

installation. Its function is based on new and sophisticated, 

patented FM data acquisition and digital signal processing.  
Modern technology is used to include 3 different detectors in a 

single case, each programmable for optimized performance at 

the specific mounting location. This results in better catch 

performance and virtually no false alarms. 
The superiority in performance of this detector is achieved by 

applying an improved version of the patented True Motion 

Recognition™ (TMR) algorithm. This advanced motion analysis 

method allows the CLIP SMA to distinguish between the true 

motion of the human body and any other disturbances that cause 

false alarms.  

After detection, the detector disarms itself to save battery power. 

It rearms (reverts to the ready state) if there is no subsequent 

detection throughout the following 2-minute period. 
The CLIP SMA includes the following features: 

  Very low current consumption 

  Microprocessor-controlled temperature compensation 

  Sealed chamber protects the optical system 

  Front cover tamper switch 

  White light protection 

  Elegantly styled, sturdy case 
Detailed coverage patterns and mounting alternatives are 

illustrated in Figures 2 through 6. 

 

Figure 2. Wall-Mount Curtain 

2.4m

 

Figure 3. Ceiling-Mount Curtain 

Figure 4. Overhead Curtain 

This

side

up

Figure 5. Curtain / Pet Alley 

OPTION A

OPTION B

DETECTION

CURTAIN

 

Figure 6. CLIP SMA on Internal Doorframe 

 

OPTICAL 
Detector Type: Dual-element low noise pyroelectric sensor. 
Number of Curtain Beams: 2 
Mounting Positions: See Figures 2 through 6. 
Range Settings: Long (6 m/18 ft), Medium (4 m/12 ft) and Short (1.2 - 
2m/6 ft) (Jumper-selected).  
ELECTRICAL 
Internal Battery: 3V Lithium battery, type CR123A. For UL installations, 
use Panasonic, GP or Sanyo only. 
Nominal Battery Capacity: 1450 mAh. 
Battery Life: 3 years (for typical use). 

Note: Inability to connect with wireless network, or wireless link quality no 
higher than 20% may significantly reduce the expected battery life. 

Battery Power Test: Performed immediately upon battery insertion 
and periodically every several hours. 
Microprocessor: 8-bit, low power CMOS. 
FUNCTIONAL 
Visual Indications (red LED):  

 

LED lights for about 3 seconds upon transmission of alarm & tamper 
messages and upon motion detection in the walk test mode.  

 

LED flashes during the power-up stabilization period (approx. 2 
min), or after restoring the cover (by pressing the tamper switch). 

 

LED does not light upon transmission of supervision messages. 

Alarm Period: Approx. 3 seconds. 

Rearm Timer: Rearms the detector 2 minutes after the last alarm.  
WIRELESS 
Frequency: 2.4 Ghz as per IEEE 802.15.4  
Tamper Alert: Reported when a tamper event occurs and in any 
subsequent message, until the tamper switch is restored. 
Supervision Message: Signaling at 24-minute intervals. 
MOUNTING  
Height: 1.8 - 2.4 m (6 - 8 ft). See Figures 2 – 6. 
Installation Options: See Figures 2 – 6. 
ENVIRONMENTAL  
Operating Temperature: -10°C to 50°C (14°F to 122°F).  
Storage Temperature: -20°C to 60°C (-4°F to 140°F).  
RFI Protection: > 20 V/m to 1000 MHz.  

Compliance with standards:  

USA: CFR 47 part 15, Canada: RSS 210

. 

ANSI/UL 639, ULC – S306 
PHYSICAL  
Dimensions (H x W x D): 105 x 35 x 30 mm (4-1/8 x 1-3/8 x  
1-3/16 in.).  
Weight (with battery): 60 g (2.1 oz).  
Color: White. 
PATENTS U.S. Patent 5,693,943 (other patents pending)