Micro-Trak Systems Inc. WT-001 Manual Do Utilizador
Wireless Remote
Operating Instructions
© 2009 P/N 50305
Micro-Trak’s Wireless Remote Accessory Kit makes it easy for
one person to remotely turn a system on and off (run/hold
function) to check for plugged or worn nozzles, general system
operation or to assist with calibration. In addition, the operator
can increase and decrease the rate remotely to verify flow
ranges. The wireless remote has a range of up to 200 ft which
allows the operator to perform these duties at a convenient,
safe and visible location. Kit includes a hand held wireless
transmitter and receiver. Simply plug the receiver cable into an
existing connector on a late model Micro-Trak console, locate
the module as far away from the console, CB radios, etc., as is
practical, and you are ready to go.
Caution Statement
Any changes or modifications not expressly approved by
the party responsible for compliance could void the user’s
authority to operate the equipment.
note: This equipment has been tested and found to comply
note: This equipment has been tested and found to comply
with the limits for a Class A digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This
equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications. Operation of the equipment in a residential
area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own
expense.
Micro-Trak Systems, Inc.
P. O. Box 99 • 111 East Leray Avenue
Eagle Lake, MN 56024
507-257-3600 • Fax: 507-257-3001
Wireless Remote
FCC ID: WZ8-WT-001
This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions:
This device may cause harmful interference, and
1.
This device must accept any interference received
2.
including interference that may cause undesired
operation.
Hold
Run
+
-
Blast
BLaSt KeY:
Used to initiate BLAST
sequence in normal operations. note:
Blast is active onLY when used with the
Roadmaster Console.
introduction
The Wireless Remote is an Optional Accessory Kit that can be
added to Micro-Trak’s Generation II Rate Controllers to provide
wireless Plus, Minus, Run, Hold and Blast functions. The wireless
hand control with five push buttons labeled Plus, Minus, RUN,
HOLD and BLAST, is used to send signals to a receiver/decoder
module connected to the console.
HoLD:
Used to place the Micro-Trak
Console in the Hold state. note: the
console master Switch and Remote Hold
Switch (if applicable) muSt be in the Run
state for the Wireless Remote Run/Hold to
work properly.
Run:
Used to place the Micro-Trak Console
in the Run state. note: the console
master Switch and Remote Hold Switch (if
applicable) muSt be in the Run state for
the Wireless Remote Run/Hold to work
properly.
Used to increase flow rate remotely
to verify flow ranges. note:
Console must be in Run state.
Used to decrease flow rate
remotely to verify flow ranges.
note: Console must be in Run
state.
operation
To use the Wireless Run/Hold functions the user muSt place
the Console in the Run state PLuS make sure if a Remote Run/
Hold switch is installed that it is also set to Run.
First press the HOLD button on the Wireless Transmitter, then
First press the HOLD button on the Wireless Transmitter, then
set the console Master Switch and Section Switches to ON and
make sure any remote Run/Hold Switch is in the RUN state.
If a power loss at the console occurs while using the Wireless
Remote, it will switch to the RUN state and the user must press
HOLD again.
If the wireless range is not satisfactory or operation is
If the wireless range is not satisfactory or operation is
intermittent, move the receiver module to a higher location,
and make sure it is not near any other electronic equipment.
Wireless Remote Button Functions
+
-