ZIONCOM ELECTRONICS LTD. WX005 Manual Do Utilizador

 The device is starting up or waiting for 

        extending.

The device is working normally.

The device is to restart.

The device is power off.

Extending successfully.

       

Green-Good;Yellow-Normal;Red-Bad.

Slow-blinking: 

The device is extending to 

                           upper Router/AP.

The device is to restart.

 No extending.

  Press the button for about 2-3 seconds

            to enable WPS.  

Wireless N Range Extender

Information in this document is subject to change without prior notice. 

Copyrights    TOTOLINK. All rights reserved. Website: http://www.totolink.net

Model No.: EX200

V1.1706

Power on. Plug the device into any wall

socket that near the router. Wait until the

System LED blinks slowly. 

1

Login. The Setting page will turn up automatically.

Click 

Extender Mode. If below window doesn’t

appear, please open a browser and enter

192.168.0.254 manually. 

3

Connect to the Extender. Using your

smart phone to search Wi-Fi

2

Extend Wi-Fi. Wait for a while, the Extender

auto-detects APs nearby. Choose your

router’s 2.4GHz SSID.

4

Configure. Enter its wireless password. Either keep

the default SSID or customize it for extended 2.4GHz

wireless network. Verify your settings and click 

Connect.

5

Wi-Fi Extended successfully while the Extend 

LED indicator keeps lighting.

6

Verify. Check the LED status to verify

whether the Wi-Fi extension is

successful.

Power on. Plug the device into any wall

socket that near the router. Wait until the

System LED blinks slowly. 

1

Press WPS button on Extender for about 2 seconds.

3

SSID: TOTOLINK_EX200 

The Extend LED flash when

connecting and turns to solid

light when connected

Press WPS button on your router for about 2 seconds. 

2

RST/WPS

Horizon Line

Host Network

Extended Network

Vertically place the Extender

Wall Socket

This port is used to connect to PC. 

Press the button for about 10 seconds, the

         device will restore to factory default settings.  

RST 

Wi-Fi: Upper router’s SSID and password

The Extend LED turns to solid light, Wi-Fi extension successful. Please refer to 

Relocate to place the Extender.

4

EX200's default Network Name (SSID) is TOTOLINK_EX200 (no encryption). 

With success repeater connection, this SSID (TOTOLINK_EX200) will change 

to the same SSID (with same encryption) of upper Router/AP. After deployment, 

just connect to the Router/AP's SSID. Congratulations, you have extended your 

WiFi coverage successfully.

 

Plug the extender into wall socket that halfway between your
router and the Wi-Fi dead zone. Wait about 30 seconds until
the Extend LED light turns solid green or yellow. If not, please
relocate it closer to your router to achieve better signal quality. 

1

In order to make full use of extender, please keep the antennas
of the extender perpendicular to the horizontal plane. See blow:

2

What should I do if I cannot access the extender’s web management

page?

A1: Make sure you have connected to the wireless network name of
      the extender. 
A2: Open any browser, enter 192.168.0.254 in the address bar and
      press Enter.
A3: Reset the extender and connect to it again. 

1

How to reset the extender to factory default settings?

Keep the extender power on, use a pin to press the RST button
on the bottom of device. When both System and Extend LED blinks,
release the button. The device will restore to factory default settings.

2

FCC warning: 

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

changes or modifications not expressly approved by the party responsible for

compliance could void the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following

measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help.

RF Exposure Statement 

This equipment complies with FCC radiation exposure limits set forth for an

uncontrolled environment .

This transmitter must not be co-located or operating in conjunction with any other

antenna or transmitter.

This equipment should be installed and operated with minimum distance 20cm

between the radiator& your body.