Grass Valley Nederland B.V. LDK4454-20 Manual Do Utilizador
20
User’s Guide - Digital Wireless System
version 10
Setting up the AMU (cont.)
AMU identification number
If more than one AMU is used, each AMU must be given a
unique identification number. The AMU identification number
is shown on the upper display on the side of the AMU. You
may choose any possible identification number as long as you
choose a different one for each AMU in the system.
unique identification number. The AMU identification number
is shown on the upper display on the side of the AMU. You
may choose any possible identification number as long as you
choose a different one for each AMU in the system.
Caution
Disconnect the power to the WCU before
opening the AMU.
opening the AMU.
To change the AMU identification number proceed as follows:
1.
Ensure power is disconnected.
2.
Open the AMU by removing the four screws underneath
the sun cover and tilt open the lid of the case.
the sun cover and tilt open the lid of the case.
3.
Find the row of three rotary switches on the main print
panel (refer to the drawing).
panel (refer to the drawing).
4.
Set the rotary switch (RC1) on the far right to the number
you want for the AMU.
5.
Close the cover and tighten the screws carefully.
Video frequency selection
If you change the frequency module on the wireless camera
adapter, it may be necessary to change the setting of the
AMU.
adapter, it may be necessary to change the setting of the
AMU.
To change the AMU frequency module setting proceed as
follows:
follows:
1.
Ensure power is disconnected.
2.
Open the AMU by removing the four screws underneath
the sun cover and tilt open the cover of the case.
the sun cover and tilt open the cover of the case.
3.
Find the row of three microswitches on the main print
panel.
panel.
4.
Use a thin screw driver to access the microswitch SW3.1.
5.
If an ISM [2.4-2.5] GHz module is used, set this switch
to the RIGHT position. For other modules set this switch
to LEFT position.
to the RIGHT position. For other modules set this switch
to LEFT position.
6.
Close the cover. Tighten the screws bit by bit
counterclockwise and one after the other to ensure
steady pressure on the waterproof gasket.
counterclockwise and one after the other to ensure
steady pressure on the waterproof gasket.
!
Note
Switches SW1, SW2 and RC3 and BP1 are
standard factory settings for the board’s logic
circuits. Do not change these switches.
standard factory settings for the board’s logic
circuits. Do not change these switches.
!
Setup switches
AMU IDENTIFIER
VIDEO CHANNEL
DATA CHANNEL
lock
error
ANT
1
2
3
POWER
AMU identification number display
Data frequency selection
If you change the Data module on the wireless camera
adapter, it may be necessary to change the setting of the
AMU.
adapter, it may be necessary to change the setting of the
AMU.
To change the AMU Data module setting proceed as follows:
1.
Ensure power is disconnected.
2.
Open the AMU by removing the four screws underneath
the sun cover and tilt open the cover of the case.
the sun cover and tilt open the cover of the case.
3.
Find the row of three rotary switches on the main print
panel (refer to the drawing).
panel (refer to the drawing).
4.
Use a thin screw driver to access the rotary switch RC2.
5.
If an 433 MHz module is used, set the switch to
position F. For other modules (e.g. 456 MHz) set the
switch to position E.
position F. For other modules (e.g. 456 MHz) set the
switch to position E.
6.
Close the cover. Tighten the screws bit by bit
counterclockwise and one after the other to ensure
steady pressure on the waterproof gasket.
counterclockwise and one after the other to ensure
steady pressure on the waterproof gasket.