Argard Co. Ltd. M20 Manual Do Utilizador

       

30

Cause:  

This may be due to a malfunction

                      with the battery. 

Solution:  Reactivate the headset by connecting  

 

it to the AC adapter and   

 

leave the headset to charge for 8 hours.

Cause: 

The headset has been left unused

 

for too long causing the battery to  

 

completely discharge.

Solution:  Reactivate the headset by connecting  

 

it to the AC adapter and   

 

leave the headset to charge for 8 hours.

Problem:  The red light does not come on  

Cause: 

The battery is already fully charged.

Solution:  Disconnect the mini USB plug

 

 

from the headset and the headset  

 

should be ready to use.

Cause: 

The headset has been left unused

 

for too long causing the battery to  

 

completely discharge.

Solution:  Reactivate the headset by connecting  

 

it to the AC adapter and   

 

leave the headset to charge for 8 hours.

Problem:  The headset is connected to the  

Cause: 

This may be due to a connection failure

 

between the device and the headset.

Solution:  Reset the device by turning it off  

 

and then back on again. Then turn  

 

the headset off and turn it on again to 

 

re-establish the connection. 

Problem:  You cannot hear the ringtone for  

an incoming call.  

Cause: 

This can happen if the phone is set to 

 

silent mode or if the ringtone has been

 

disabled.

Solution:  Change the phone settings to enable 

 

the incoming call ringtone.

Problem:  There is static noise during  

Cause: 

The headset uses radio frequency  

 

waves at the lowest transmission  

 

power levels possible in order that  

 

minimum battery power is used, at  

 

the same time as meeting the signal  

 

efficiency standards for Bluetooth®  

 

Class 2. The distance between  

 

the headset and device should be  

 

kept to a minimum wherever possible.

Solution:  For optimum sound quality, wear  

 

the headset on the same side of  

 

your body as the mobile phone. 

Problem:  The headset has been unexpectedly

Cause: 

It is a normal feature of the headset 

 

to go into low-energy mode after  

 

90 minutes of inactivity. Many  

 

Bluetooth®-enabled devices support  

 

this mode, however, if your mobile  

 

phone does not support this, the  

 

headset will disconnect from the  

 

device. 

Solution:  Press

 

the FUNCTION button once to  

 

reconnect and answer the call.  

 

It may, however, take an  extra 2-3  

 

seconds to make the connection. 

 

Cause: 

This may be due to

 

improper usage  

 

or it is likely that the headset has  

 

been stored at too high temperature  

 

which can cause the processor chip  

 

to malfunction.

Solution:  The headset should be reset. Press and 

 

hold down the VOLUME UP, VOLUME 

 

DOWN and FUNCTION buttons 

 

simultaneously for approximately

 

10 seconds. The red light will flashes

 

1 time to indicate a headset shutdown 

 

and reset. Then press the FUNCTION 

 

button once more to restart the 

 

headset for normal use.

The headset has been designed and produced 

using the latest technology, and should be looked 

after carefully. The following recommendations will 

help you to use the headset in accordance with the 

requirements of the warranty, and will help to 

extend its lifetime.

•  Avoid storing the headset in humid, dusty or 

moist conditions, or at temperatures over 

45ºC. These conditions may cause the 

electronic components to degrade.

•  Avoid storing the headset in very cold 

conditions (below -10ºC). When the headset is 

turned on at these temperatures, condensa-

tion is created inside the headset and may 

damage the electronic circuits. 

•  Avoid using the headset in very hot 

conditions, as the heat may shorten the 

lifespan of the electronic equipment and may 

also damage the battery. 

•  Avoid knocking or shaking the headset. 

Careless usage may damage the internal 

circuits.

•  Do not clean the headset with strong 

chemicals or substances, as they may damage 

its surface.

•  Do not attempt to open the headset. The 

battery is not user-replaceable and replacing it 

will  invalidate the warranty.

These recommendations will help to extend the 

lifetime of your headset. If you have any problems 

with the headset, please refer to the warranty 

section of this guide.

This device complies with Part 15 of the FCC Rules. 

Operation is subject to the following two 

conditions.

• This device may not cause harmful interference. 

• This device must accept any interference 

received, including interference that may cause 

undesired operation.

This product is CE marked according to provisions 

of the R&TTE Directive.

Bluetooth®

The Bluetooth® trademark and logos are owned by 

Bluetooth® SIG, Inc. and any use of such trademarks 

by Argard are under license. 

 

Argard Co., Ltd, the producer of this Bluetooth® 

headset, guarantees to provide quality after-sales 

support and service to buyers or users of this 

product, under the following conditions:

1.  The product warranty is valid for a period of 

one (1) year from the date of purchase.

2.  The buyer must produce a receipt or other 

documentation showing the date, time and 

place where the product was purchased.

3.  The buyer is not covered by this warranty      

under the following conditions.

•   The product has been damaged due to 

improper usage or storage, falling or being 

dropped hard on the ground, or coming into 

direct contact with steam or water. 

•   The product has been repaired or modified 

by an unauthorized person.

•   The product has been sent for repairs after 

the warranty has expired, in which case the 

company will charge for the service at the 

normal cost.

•   The battery has been modified, or an 

unsuitable battery has been used.

•   Charging equipment other than that 

provided with the headset has been used.

4. If a problem occurs during the warranty period, 

the buyer should send or take the product to 

the original vendor.

All information regarding this warranty or the 

product may be modified without notice.

www.argard.com

If your Bluetooth®-enabled device supports voice 

dialing, you can make a voice dialing call by first 

pressing the FUNCTION button. Once prompted, 

proceed as you would normally with the voice 

dialing on your mobile phone. 

To cancel voice dialing, press the FUNCTION 

button.

A call can be transferred from your mobile phone 

to the headset and vice versa. 

To transfer a call from the headset to the mobile 

phone, press the FUNCTION button twice. 

To transfer a call from the mobile phone to the 

headset, press the FUNCTION button once. 

To redial the last number called, press the 

FUNCTION button twice. A ‘beeping’ sound will be 

heard, and the last number called will be redialed.

To cancel , press the FUNCTION button once.

To receive a waiting call and hold an active call, 

press and hold down the FUNCTION button for 

approximately 3 seconds.

To Accept waiting call and release  active call

Press FUNCTION button 2 twice.

To alternate between the active call and the 

waiting call, press  hold down the FUNCTION 

button for  approximately 3 seconds.

To Release  all held call ,press and hold the VOLUME 

DOWN or  VOLUME UP button for approximately 3 

seconds.

To use the three-way calling function, press and 

hold the FUNCTION button for approximately 8 

seconds.

To end the three-way calling function,press the 

FUNCTION button twice.

To connect Multi-party calls and remove your self 

from the conversation press and hold the VOLUME 

DOWN and VOLUME UP button for approximately 7 

seconds.

A warning tone will sound if the battery is low , and 

the flashing blue light will change to a red light, 

with 1 flashes every 10 seconds.

Power on

Blue light long flashes once

Power off

Red light long flashes once

Blue light flashes once

Pairing mode

Blue and red light 

alternating flashes

Stand-by mode,

During call

Blue light flashes once 

every 10 seconds

Blue light rapid flashes 

until the call is received

Low battery

Red light flashes once 

every 10 seconds

Pairing successful

right

right

left

left

30

30

Turn the earbud to an angle of approximately 30 

degrees from the direction of the headset 

depending on which side of the body you wish to 

wear the headset.

   

Once the earbud is in position, insert the headset 

into your ear canal according to the pictures below.

To turn the headset on, press the FUNCTION 

button until you see the blue light long flashes 

once time and you hear 4 tones.  

For the headset to function, it must first be paired 

(linked) with a Bluetooth®-enabled device like a 

mobile phone. To do this, the headset must be 

turned on. Press and hold down the FUNCTION 

button until blue light long flashes once time. Keep 

pressing the FUNCTION button until there are 

alternate rapid red and blue flashing lights. Then 

release the FUNCTION button.

Use your Bluetooth®-enabled device’s menu (see 

relevant user manual) to search for the headset and 

select the M20 once it finds it. When the device 

requests a passkey, enter 0000 (four zeros) and 

then press YES or OK. Your device is now paired to 

the headset for future use.

To turn the headset off, hold the FUNCTION button 

down until you see the red light long flashes once 

time.

To answer an incoming call, press the FUNCTION 

button. 

To end a call, press the FUNCTION button again. 

To reject an incoming call, hold the FUNCTION 

button down for 2 seconds.

Use the VOLUME UP button to increase the volume 

and the VOLUME DOWN button to decrease the 

volume. (See Overview.)

 

folding line

die cut line

Incoming call

Use only the supplied adaptor.

Meaning of WEEE symbol

e.g.                this symbol indicating separate

collection electrical and electronic equipment.

Modification not expressly approved by this

company void the user's authority to operate

the equipment.

Less than 20% charged

Red light flashes

20%-99% charged

Red light is on continue

Fully charged

Blue light is on continue

30

30

ARGARD M20 user manual

• a headset with a medium-sized earbud fitted

• an AC adapter

• 2 spare earbuds - 1 large and 1 small.

Weight: 12.5 grams

Size: 27 mm x 50 mm x 10.5 mm

Talk time: up to 6.0 hours

Standby time: up to 200 hours

Bluetooth® version: 2.0

Microphone: Dual Microphone

Noise canceling /Digital Signal Processing

The headset must be fully charged before you use 

it for the first time. Connect the mini USB plug from 

the AC adapter to the headset and plug the AC 

adapter into the electrical socket and charge the 

headset for 8 hours.

 

A red light will come on while the headset is 

charging. If it fails to come on, press the FUNCTION 

button to activate it. The red light will go off once 

the headset is fully charged. After the inital charge, 

recharging takes approximately 3 hours.

The earbud attached to the headset is medium-

sized. Large and small earbuds are also included. 

Choose the size that works best for you. 

spare earbuds

(1 small and 1 large)

headset

AC adapter

mini USB plug

supplied earbud

3 earbuds supplied
(small, medium 
and large)

FUNCTION button

VOLUME UP button

VOLUME DOWN button

30