IKUSI ELECTRONICA S.L. TR2400-MCX Manual Do Utilizador
CATEGORIA DE DOCUMENTO
TIPO DE DOCUMENTO
Preparado por / Prepared by
No. / Num.
Pág. / Page
Luis Vidaurreta
2 / 4
Aprobado por / Approved by
Fecha / Date
Rev./ Rev. Archivo / File
17/10/2017
PVTTR2400 installation
manual.docx
3.
INSTALLATION
Make sure that the crane is stopped for the entire duration of the assembly process, keep the work area free
and wear protective clothing.
Park the crane and position stop-ends (if these are not available use appropriate signs) at a suitable distance
so that other cranes on the same runway do not hit it.
Check the power-supply voltage and turn off the mains switch, disconnecting the wiring and connector
between the receiver and the electrical cabinet of the machine.
Remember that the receiver has several voltage-powered circuits. Even when the power has been cut off,
there is still a risk of electrical shocks.
and wear protective clothing.
Park the crane and position stop-ends (if these are not available use appropriate signs) at a suitable distance
so that other cranes on the same runway do not hit it.
Check the power-supply voltage and turn off the mains switch, disconnecting the wiring and connector
between the receiver and the electrical cabinet of the machine.
Remember that the receiver has several voltage-powered circuits. Even when the power has been cut off,
there is still a risk of electrical shocks.
4.
FCC/ISED REGULATORY NOTICES
Modification statement
IKUSI ELECTRONICA, S.L.
has not approved any changes or modifications to this device by the
user. Any changes or modifications could void the user’s authority to operate the equipment.
IKUSI ELECTRONICA, S.L.
n’approuve aucune modification apportée à l’appareil par l’utilisateur,
quelle qu’en soit la nature. Tout changement ou modification peuvent annuler le droit d’utilisation
de l’appareil par l’utilisateur.
Interference statement
This device complies with Part 15 of the FCC Rules and Industry Canada license-exempt RSS
standard(s). Operation is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including interference that may
cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne
doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
Wireless notice
This device complies with FCC/ISED radiation exposure limits set forth for an uncontrolled
environment and meets the FCC radio frequency (RF) Exposure Guidelines and RSS‐102 of the ISED
radio frequency (RF) Exposure rules. Antenna gain must be below:
de l’appareil par l’utilisateur.
Interference statement
This device complies with Part 15 of the FCC Rules and Industry Canada license-exempt RSS
standard(s). Operation is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including interference that may
cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne
doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
Wireless notice
This device complies with FCC/ISED radiation exposure limits set forth for an uncontrolled
environment and meets the FCC radio frequency (RF) Exposure Guidelines and RSS‐102 of the ISED
radio frequency (RF) Exposure rules. Antenna gain must be below:
Frequency band
Antenna Gain [dBi]
2.4 GHz
13.79
This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
This device needs to be installed and used on distance greater than 20 cm from human body.
transmitter.
This device needs to be installed and used on distance greater than 20 cm from human body.