Wilson Electronics LLC 460033 Manual Do Utilizador
5
Contact Wilson Electronics Technical Support Team with any questions at
866-294-1660 or email: tech@wilsonelectronics.com
Signal Booster Specifications
4G Marine Antenna™
Product Number
470133
Model Number
460033
FCC ID
PWO460033
IC ID
4726A-460033
Frequency
698-716 MHz, 729-746 MHz, 777-787 MHz, 824-894 MHz, 1850-1995 MHz, 1710-1755/2110-2155 MHz
Power output for single cell
phone (Uplink) dBm
phone (Uplink) dBm
700
MHz
Band12/17
700
MHz
Band13
800
MHz
1700
MHz
1900
MHz
21.5
24.8
24.10
23.90
26.00
Power output for single cell
phone (Downlink) dBm
phone (Downlink) dBm
700
MHz
Band12/17
700
MHz
Band13
800
MHz
2100
MHz
1900
MHz
5.8
8.0
10.1
5.8
-1.5
Noise Figure
5 dB nominal
2-Year Warranty
Wilson Electronics Signal Boosters are warranted for two (2) years against defects in workmanship and/or
materials. Warranty cases may be resolved by returning the product directly to the reseller with a dated proof
of purchase.
materials. Warranty cases may be resolved by returning the product directly to the reseller with a dated proof
of purchase.
Antennas may also be returned directly to the manufacturer at the consumer’s expense, with a dated proof
of purchase and a Returned Material Authorization (RMA) number supplied by Wilson Electronics. Wilson
Electronics shall, at its option, either repair or replace the product. Wilson Electronics will pay for delivery of the
repaired or replaced product back to the original consumer if located within the continental U.S.
of purchase and a Returned Material Authorization (RMA) number supplied by Wilson Electronics. Wilson
Electronics shall, at its option, either repair or replace the product. Wilson Electronics will pay for delivery of the
repaired or replaced product back to the original consumer if located within the continental U.S.
Replacement products may include refurbished weBoost products that have been recertified to conform with
product specifications.
product specifications.
This warranty does not apply to any antennas determined by Wilson Electronics to have been subjected to
misuse, abuse, neglect, or mishandling that alters or damages physical or electronic properties.
misuse, abuse, neglect, or mishandling that alters or damages physical or electronic properties.
RMA numbers may be obtained by contacting Technical Support at 866-294-1660.
Disclaimer: The information provided by Wilson Electronics, LLC is believed to be complete and accurate.
However, no responsibility is assumed by Wilson Electronics, LLC for any business or personal losses
arising from its use, or for any infringements of patents or other rights of third parties that may result from
its use.
However, no responsibility is assumed by Wilson Electronics, LLC for any business or personal losses
arising from its use, or for any infringements of patents or other rights of third parties that may result from
its use.
Copyright © 2017 Wilson Electronics, LLC. All rights reserved.
Each Signal Booster is individually tested and factory set to ensure FCC compliance. The Signal Booster cannot be adjusted without
factory reprogramming or disabling the hardware. The Signal Booster will amplify, but not alter incoming and outgoing signals in order
to increase coverage of authorized frequency bands only. If the Signal Booster is not in use for five minutes, it will reduce gain until a
signal is detected. If a detected signal is too high in a frequency band, or if the Signal Booster detects an oscillation, the Signal Booster
will automatically turn the power off on that band. For a detected oscillation the Signal Booster will automatically resume normal
operation after a minimum of 1 minute. After 5 (five) such automatic restarts, any problematic bands are permanently shut off until the
Signal Booster has been manually restarted by momentarily removing power from the Signal Booster. Noise power, gain, and linearity
are maintained by the Signal Booster’s microprocessor.
factory reprogramming or disabling the hardware. The Signal Booster will amplify, but not alter incoming and outgoing signals in order
to increase coverage of authorized frequency bands only. If the Signal Booster is not in use for five minutes, it will reduce gain until a
signal is detected. If a detected signal is too high in a frequency band, or if the Signal Booster detects an oscillation, the Signal Booster
will automatically turn the power off on that band. For a detected oscillation the Signal Booster will automatically resume normal
operation after a minimum of 1 minute. After 5 (five) such automatic restarts, any problematic bands are permanently shut off until the
Signal Booster has been manually restarted by momentarily removing power from the Signal Booster. Noise power, gain, and linearity
are maintained by the Signal Booster’s microprocessor.