SGEG N.A. INC. FBTT5002 Manual Do Utilizador

Application and performance specification 

Electronic ballast for 14Wx2, 21Wx2, 24Wx2, 39Wx2, 54Wx2, 

Description 
Active power factor correction.  PF≧0.99 
Low harmonic distortion  . 

THD≦10% 

Low lamp current crest factor.  CF≦1.6 

Warn (Rapid) start. 
Long Life 
De-active lamp protection 

Model Line 

 
Volts 

Lamp 
 
type 

Input 
 
watts 

Normal 
 
Line amps 

Power 
 
factor 

Total 
Harmonic 
distortion 

Crest 
 
factor 

PMFBTT514x2 120V/60Hz  T5 14W 

33W 

0.28A 

＞

0.99

 

<10% <1.6 

PMFBTT521x2 120V/60Hz  T5 21W 

50W 

0.42A 

＞

0.99

 

<10% <1.6 

PMFBTT524x2 120V/60Hz  T5 24W 

63W 

0.52A 

＞

0.99

 

<10% <1.6 

PMFBTT539x2 120V/60Hz  T5 39W 

91W 

0.78A 

＞

0.99

 

<10% <1.6 

PMFBTT554x2 120V/60Hz  T5 54W 

125W 

1.05A 

＞

0.99

 

<10% <1.6 

 
Performance 

 

 

 

 

 

 

 

Safety 

Meets FCC Part 18 (Class A) For EMI 

 

 

 

UL listed 

  Non-consumer 

limits 

Application: 

 

 

 

 

 

 

 

Physical parameters 

Minimum starting temperature  -18℃   Mounting 

length 416mm 

Maximum ambient temperature  40℃ 

    (center 

to 

center) 

Maximum case temperature 

75℃ 

   Overall 

length 

 430mm 

 

 

 

 

 

 

 

 

 

 

Width 

 

 

30mm 

 

 

 

 

 

 

 

 

 

 

Height 

 

 

26mm 

 
This light device has been tested and found to comply with the limits for Consumer RF Lighting 
Device, pursuant to Part 18 of the FCC Rules. These limits are designed to provide reasonable 
protection against harmful interference in a residential installation.    This equipment generates, uses 
and can radiate radio frequency energy and, if not installed and used in accordance with the 
instructions, may cause harmful interference to radio communications.    However, there is no 
guarantee that interference will not occur in a particular installation. 
1.  Use only on 120 volt, 60 hertz. 
2.  Never disassemble or modify - any changes could void the user's authority to operate this device. 
3.  Not for use in totally enclosed fixtures. 
4.  Risk of electric shock - do not use where directly exposed to water. 
5.  This device is not intended for use with emergency exit fixtures or emergency exit lights. 
6.  This product could produce interference when used near a TV, radio, wireless remote control or 

maritime safety communications equipment operating between 0.45-30 MHz.    If interference 
should occur, move the lamp away from the appliance a distance into a different outlet. 

7.  To prevent burns, do not touch the bulb during operation or immediately after switching off. 
8.  Not for use with dimmers, electronic timer or photocell devices or occupancy sensor. 
 
Warranty 
Universal lighting technologies warrants to the purchaser that each electronics ballast will be