Broadcom Corporation BRCM1084 Manual Do Utilizador
OEM Installation Guidance Document
For Broadcom BCM943228Z
FCC ID: QDS-BRCM1084; IC: 4324A-BRCM1084
Page 4 of 9
gain of 3.33dB/2.4GHz and 6.21dBi/5GHz. Any other detachable antennas, with a
different type or having a gain greater than 3.33dB/2.4GHz and 6.21dBi/5GHz are
strictly prohibited for use with this device. The required antenna impedance is 50 ohms.
Caution: (this only applicable to UNII device)
(i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce
the potential for harmful interference to co-channel mobile satellite systems;
(ii) the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and
5470-5725 MHz shall comply with the e.i.r.p. limit; and
(iii) the maximum antenna gain permitted for devices in the band 5725-5825 MHz shall
comply with the e.i.r.p. limits specified for point-to-point and non point-to-point
operation as appropriate.
High power radars are allocated as primary users of the 5.25 to 5.35 GHz and 5.65 to
5.85 GHz bands. These radar stations can cause interference with and/or damage this
device.
Caution: Exposure to Radio Frequency Radiation.
To comply with RSS 102 RF exposure compliance requirements, for mobile
configurations, a separation distance of at least 20 cm must be maintained between the
antenna of this device and all persons. This device must not be co-located or operating in
conjunction with any other antenna or transmitter.
System integrators must include a label with “Contains IC: 4324A-BRCM1084” on the
end product. Industry Canada user statements should be provided in both English and
French, at the time each product is offered for sale or lease in Canada.
For portable configurations, antennas must be installed in the display section or
underneath the keyboard in Netbook/notebook/laptop/tablet computers to provide at least
5mm separation distance from the transmitting antenna to the body of user, or any other
person during normal operating condition.
different type or having a gain greater than 3.33dB/2.4GHz and 6.21dBi/5GHz are
strictly prohibited for use with this device. The required antenna impedance is 50 ohms.
Caution: (this only applicable to UNII device)
(i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce
the potential for harmful interference to co-channel mobile satellite systems;
(ii) the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and
5470-5725 MHz shall comply with the e.i.r.p. limit; and
(iii) the maximum antenna gain permitted for devices in the band 5725-5825 MHz shall
comply with the e.i.r.p. limits specified for point-to-point and non point-to-point
operation as appropriate.
High power radars are allocated as primary users of the 5.25 to 5.35 GHz and 5.65 to
5.85 GHz bands. These radar stations can cause interference with and/or damage this
device.
Caution: Exposure to Radio Frequency Radiation.
To comply with RSS 102 RF exposure compliance requirements, for mobile
configurations, a separation distance of at least 20 cm must be maintained between the
antenna of this device and all persons. This device must not be co-located or operating in
conjunction with any other antenna or transmitter.
System integrators must include a label with “Contains IC: 4324A-BRCM1084” on the
end product. Industry Canada user statements should be provided in both English and
French, at the time each product is offered for sale or lease in Canada.
For portable configurations, antennas must be installed in the display section or
underneath the keyboard in Netbook/notebook/laptop/tablet computers to provide at least
5mm separation distance from the transmitting antenna to the body of user, or any other
person during normal operating condition.
French:
Cet appareil est conforme avec Industrie Canada exempts de licence standard RSS (s)
l'opération est soumise aux deux conditions suivantes: . ( 1) ce dispositif ne doit pas
causer d'interférences et ( 2) cet appareil doit accepter toute interférence , y compris les
interférences qui peuvent provoquer un mauvais fonctionnement de l'appareil.
Conformément à la réglementation d'Industrie Canada, cet émetteur radio ne peut
fonctionner à l'aide d'une antenne d'un type et maximum ( ou moins ) Gain approuvé pour
l'émetteur par Industrie Canada. Afin de réduire le risque d'interférence avec d'autres
utilisateurs, le type d'antenne et son gain doivent être choisi que la puissance isotrope
rayonnée équivalente (PIRE ) ne dépasse pas ce qui est nécessaire pour une
communication réussie .
l'opération est soumise aux deux conditions suivantes: . ( 1) ce dispositif ne doit pas
causer d'interférences et ( 2) cet appareil doit accepter toute interférence , y compris les
interférences qui peuvent provoquer un mauvais fonctionnement de l'appareil.
Conformément à la réglementation d'Industrie Canada, cet émetteur radio ne peut
fonctionner à l'aide d'une antenne d'un type et maximum ( ou moins ) Gain approuvé pour
l'émetteur par Industrie Canada. Afin de réduire le risque d'interférence avec d'autres
utilisateurs, le type d'antenne et son gain doivent être choisi que la puissance isotrope
rayonnée équivalente (PIRE ) ne dépasse pas ce qui est nécessaire pour une
communication réussie .