Leviton Manufacturing Co. Inc. DDMX1 Manual Do Utilizador

PRELIMINARY

Single Pole (One location) or 3-Way (Multi-location)

Cat. No. DDE06-BL - 600W Incandescent, 300W LED/CFL, 600W ELV

120VAC, 60Hz

1 - #12 w/ 1 to 3 #14, #16 or #18

2 - #12 w/ 1 or 2 #16 or #18

1 - #14 w/ 1 to 4 #16 or #18

2 - #14 w/ 1 to 3 #16 or #18

DI-000-DDE06-02A-X0

Slotted/Phillips Screwdriver 

Electrical Tape 

Pliers 

Pencil 

  Cutters 

 Ruler

In multi-dimmer installations, the reduction of the dimmer’s capacity may 

be required. Refer to the chart for maximum load per dimmer. 

 No derating is required for LED or CFL bulb applications.

If installing Dimmer in a single device application, proceed with the 

 section. If installing Dimmer in a 

multi-device application, proceed as follows:

Your device may include color options. To change color of the face 

proceed as follows:

 Use check boxes           when Steps are completed.

at circuit breaker or fuse and test that power 

is off before wiring!

 If the wiring in your wall box does not resemble any 

of these conigurations, consult an electrician.

  Line (Hot)

  Neutral

  Ground

  Load 

  Line or Load

  Neutral

  Ground

  First Traveler – note color

  Second Traveler – note color

 For 3-Way applications, note that one of the screw terminals 

from the old switch being removed will usually be a different color (Black) 

or labeled Common. Tag that wire with electrical tape and identify as the 

common (Line or Load) in both the dimmer wall box and remote wall box.

•   Pull off pre-cut insulation from dimmer leads.
•   Make sure that the ends of the wires from the wall box are straight 

.

•   Remove insulation from each wire in the wall box as shown.
•   For Single-Pole Application, go to Step 4a.
•   For 3-Way Matching Remote (w/LEDs) Application, go to Step 

 Use check boxes           when Steps are completed.

at circuit breaker or fuse and test that power 

is off before wiring!

 If the wiring in your wall box does not resemble any 

of these conigurations, consult an electrician.

  Line (Hot)

  Neutral

  Ground

  Load 

  Line or Load

  Neutral

  Ground

  First Traveler – note color

  Second Traveler – note color

Pull off pre-cut insulation from dimmer leads. Make sure that 

the ends of the wires from the wall box are straight (cut if 

. Remove insulation from each wire in the wall box 

as shown:

Low-voltage dimmers are rated in Volt-Amps (VA). The maximum bulb wattage 

is determined by the eficiency of the transformer in the low-voltage lighting 

system. Transformer eficiencies will vary from different manufacturers; 

consider 80% eficient as average. Use the chart to determine maximum bulb 

wattage for typical transformer eficiency ratings.

400W

500W

600W

560W

Rating
1000VA

800W

640W

The next generation of lighting control technology is here with the new 

Decora

®

 Digital Dimmer with Bluetooth

®

 Technology. This innovative 

device works using the Leviton Decora

®

 Digital Dimmer & Timer app 

that can be easily downloaded to smartphones or tablets and paired 

to the Leviton Dimmer using Bluetooth

®

 technology. Decora

®

 Digital 

Devices give users point-to-point local control to automate lighting, 

bridging the gap between standard dimmers and whole-house 

automation systems. 
The Decora

®

 Digital Dimmer is a powerful device – combining the best 

of Leviton dimmer and timer functions with today’s mobile technology 

for impressive results. The simple touch of a inger following the 

intuitive on-screen guide makes it more convenient than ever to 

manage lighting for home activities or to ensure a "lived-in" look while 

away. Plus, the Decora

®

 Digital Dimmer is Universal and compatible 

with LED, CFL, Incandescent or Halogen loads.
Use of the app allows greater lexibility for accurate timer functionality 

and makes pushing buttons for timed events a tedious chore of the 

past.
The Leviton Decora

®

 Digital Dimmer & Timer app can be easily 

downloaded to mobile devices and is compatible with Android and iOS 

smartphones or tablets. The app is easy to use with simple, intuitive  

on-screen menu options to independently control dimmers and 

switches throughout the home.
Decora

®

 Digital Devices are ideal for living rooms, bedrooms, kitchens, 

dining rooms, home ofices, outdoor lighting or anywhere full control of 

lighting is desired.
Compatibility:

 

Requires device with Bluetooth

®

 4.0 (BT LE) or later and iOS 6.0 and 

later. Compatible with iPhone, iPad, and iPod touch or Android 4.0 and 

later.

•   Soft fade ON/OFF

•   ON/OFF LED and Brightness level LED 

•   Three way communication  

•   Ease of installation – No new wiring

 CONNECT AN ELECTRONIC LOW-VOLTAGE DIMMER 

ONLY TO THE PRIMARY (HIGH-VOLTAGE) SIDE OF A MAGNETIC 

LOW-VOLTAGE TRANSFORMER.
NOTE:

 The DDE06 dimmer requires a neutral wire connection.

•   Green or bare copper wire in wall box to Green dimmer lead.

•   Line Hot wall box wire to Black dimmer lead.

•   Load wall box wire to Red dimmer lead.

•  Line Neutral wall box wire to White dimmer lead.

•   Yellow/Red dimmer lead should have Red insulation label afixed.

  NOTE: If insulating label is not afixed to Yellow/Red dimmer lead, use 

electrical tape to cover.

•   Proceed to Step 5.

:

 at circuit breaker or fuse and test that power is off before wiring!

install to control a receptacle, a motor- or a transformer-operated appliance. 

To be installed and/or used in accordance with electrical codes and regulations.

•   If you are unsure about any part of these instructions, consult an electrician.

•   Use with magnetic low voltage transformers, incandescent, or 120V halogen ixtures only. Use a Leviton electronic low voltage dimmer to control electronic (solid state) low voltage transformers.

•   The Decora

®

 DDE06 dimmer is not compatible with standard 3-way or 4-way switches. It must be used with a Decora

®

 Digital remote for multi-location control, such as the DD00R-DL.

•   Maximum wire length from dimmer to all installed remotes cannot exceed 300 ft.

:

•   Dimmer may feel warm to the touch during normal operation.
•   Recommended minimum wall box depth is 2-3/4".
•   Use this device WITH COPPER OR COPPER CLAD WIRE ONLY.
•   Use with compatible dimmable LED, CFL bulbs, incandescent or 120V halogen ixtures only. For a list of compatible LED and CFL bulbs refer to www.leviton.com.
•   When multiple bulbs are used with one dimmer DO NOT mix bulb types. All bulbs shall be either LED; CFL or incandescent. Using the same make/model of each bulb will enhance 

dimmer performance.

 The matching remote must be installed in a wall box with a 

Line Hot connection and a Neutral connection. A Neutral wire to the 

matching remote needs to be added as shown.
NOTE:

 Maximum wire length from dimmer to all installed remotes 

cannot exceed 300 ft (90 m).
•  Green or bare copper wire in wall box to Green terminal screw.

•  Line Hot (common) wall box wire identiied (tagged) when removing 

old switch and First Traveler to Remote terminal marked "BK".

•  Second Traveler wall box wire from dimmer to remote terminal screw 

marked "YL/RD" (note wire color). This traveler from the remote 

must go to Yellow/Red dimmer lead.

•  Line Neutral wall box to remote terminal screw marked "WH".

 The DDE06 dimmer must be installed in a wall box that has a 

Load connection and a Neutral connection.
•  Green or bare copper wire in wall box to Green dimmer lead.

•  Load wall box wire identiied (tagged) when removing old switch to 

Red dimmer lead.

•  First Traveler Line Hot to Black dimmer lead.

•  Remove Red insulating label from Yellow/Red dimmer lead.

•  Second Traveler wall box wire (note color as above) to 

Yellow/Red dimmer lead. This traveler from the dimmer must go to 

the terminal screw on the remote marked "YL/RD".

•  Line neutral wall box wire to White dimmer lead.

•  Proceed to Step 5.