Leviton Manufacturing Co. Inc. RZC04 Manual Do Utilizador

NOTES:
•

If using a non-Leviton Programmer/Remote, refer to the

Programmer/Remote instruction sheet.

•

4-Scene controllers incuded into a Z-Wave

®

network must be

updated after you have included all other devices.

•

If using the VRCPG Install Checklist feature, go to step C.

A)  If using a Leviton Z-Wave

®

Programmer/Remote, Cat. No. VRCPG,

press the Menu button and scroll down to System Setup. Press

the center button to select System Setup Menu. Choose Advanced

Settings. Press the center button to select Network. Press the center

button to <Include Node>.

B)  If using VRCPG Programmer/Remote, you will be prompted to place

4-Scene controller into programming mode.

C)  To access Program mode, press and hold

buttons 1 and 3 (refer to figure). Wait

5 seconds until the LED turns Amber.

Release the buttons and the LED will blink

Amber. You are now in Programming mode.

NOTE: If the LED on the 4-scene controller

turns solid Red while including, there has

been a communication error.

D)  While standing close to the 4-Scene

controller (approximately 1 ft.), press the

center button on the Programmer/Remote

to <Include> device in the network.

NOTE: If the LED on the 4-scene controller

turns solid Red while including, there has

been a communication error.

NOTE: Only one device may be included at any time.

E)  The Primary Programmer/Remote will assign a Home ID, Node ID,

and Name for this device.

NOTE: This information will be stored in the Programmer/Remote to

be used for future reference.

NOTE: You may name or edit your device at this time.

F)  The 4-Scene controller is now installed in the network.

:

•  ON/OFF LED for remote load status.
•  To be installed and/or used in accordance with appropriate electrical codes and regulations.
•  If you are unsure about any part of these instructions, consult a qualified electrician.
•  Vizia RF +

TM

VRCS4 controller does not control the load, but provides scene applications to operate with Vizia RF +

TM

dimmers/switches.

•  Recommended minimum wall box depth is 2-1/2".

:

•  Can call up four (4) scene ON/OFF with advanced Programming Remote (see VRCPG).
•  For a complete set-up, a controller supporting the advanced Z-Wave

®

scene features is needed, such as the advanced Programming Remote (VRCPG).

•  Disconnect power at circuit breaker or fuse when servicing, installing or removing fixture.
•  Use this device only with copper or copper clad wire. With aluminum wire use only devices marked CO/ALR or CU/AL.

Cat. No. VRCS4-1L

120VAC, 60Hz

DI-000-VRCS4-02B-X0

Slotted/Phillips Screwdriver

Electrical Tape

Pliers

Pencil

Cutters

Ruler

OFF POWER at circuit breaker or fuse and test that power is off

before wiring!

This 4-Scene controller can be wired using side wire terminal

screws or through backwire openings. Choose appropriate wire

stripping specifications accordingly.

•  Make sure that the ends of the wires from the wall box are

Back wire openings use #14-12 AWG

solid wire copper only.

Side wire terminals accept

#14 AWG solid wire copper only.

•  Green or bare copper wire in wall box to Green terminal screw.

•  Line Hot wall box wire to terminal screw marked "BK".

•  Line Neutral wall box wire to terminal screw marked "WH".

1. Line (Hot)

2. Neutral

3. Ground

NOTE: If the wiring in your wall box does not resemble this

configuration, consult a qualified electrician.

Leviton’s Vizia RF +

TM

components are designed to communicate

with each other via Radio Frequency (RF) to provide remote control

of your lighting. Using RF technology allows Leviton to provide the

greatest signal integrity possible. Each module in Leviton’s Vizia RF +

TM

component line is a Z-Wave

®

enabled device. In a Z-Wave

®

network,

each device is designed to act as a router. These routers will re-transmit

the RF signal from one device to another until the intended device

is reached. This ensures that the signal is received by its intended

device by routing the signal around obstacles and radio dead spots.

This 4-Scene Controller is meant to control special scene enabled

Z-Wave

®

products. To control groups of devices that are mixed or do

not support scene command class use the Leviton 4-Zone Controller

(VRCZ4). Setting up this device requires specific advanced controller

functionalities, your controller must be able to associate device to groups

and must be able to control the scene controller configuration commands

such as the advanced Programming Remote (VRCPG).

•  This is a Z-Wave

®

Controller

•  Scene control without traveler wires
•  Can call 4 scenes
•  ON/OFF LED
•  Two way communication
•  RF reliability
•  Ease of installation – No new wiring
•  Compatible with other Z-Wave

®

enabled devices

Your 4-Scene controller includes three color options. The controller ships

with the White frame attached. To change color of frame, proceed as

follows:

After frame is removed, remove existing push buttons and replace them

with desired color change push buttons. To change the DIM/BRIGHT

button, before mounting frame, press out DIM/BRIGHT button (bottom)

from back of frame and press in from front of frame new DIM/BRIGHT

button. To make IR capable, replace with a DIM/BRIGHT button that has

the IR window.

NOTE: Use check boxes when Steps are completed.

•  Position all wires to provide room in

outlet wall box for device.

•  Ensure that the word “TOP” is facing up

on device strap.

•  Partially screw in mounting screws in

wall box mounting holes.

 NOTE: Dress wires with a bend as

shown in diagram in order to relieve

stress when mounting device.

•  Restore power at circuit breaker or fuse.
•  LED should turn ON.
 If lED does not turn ON, refer to the 

Restore power at circuit breaker or fuse. 

Installation may now be completed by

tightening mounting screws into wall box.

Attach wallplate.