Leviton Manufacturing Co. Inc. RZC0P Manual Do Utilizador

Rated: 120VAC, 60Hz

DI-000-RZC0P-00A-X3

Leviton’s Vizia

TM

 RF components are designed 

to communicate with each other via Radio 

Frequency (RF) to provide remote control 

of your lighting. Using RF technology allows 

Leviton to provide the greatest signal integrity 

possible. Each module in Leviton’s Vizia

TM

 

RF component line is a Z-Wave

TM

 enabled 

device. In a Z-Wave

TM

 network, each device is 

designed to act as a router. These routers will 

re-transmit the RF signal from one device to 

another until the intended device is reached. 

This ensures that the signal is received by its 

intended device by routing the signal around 

obstacles and radio dead spots. The Plug-in 

Serial Interface Module is compatible with any 

Z-Wave™ enabled network, regardless of the 

manufacturer and can also be used with other 

devices displaying the Z-Wave™ logo. 

Remember to exercise good common sense 

when using the Timer features of your remote, 

especially when scheduling unattended 

devices. There can be some unexpected 

consequences if not used with care. For 

example, an empty coffee pot can be remotely 

turned on. If that should happen, your coffee 

pot could be damaged from overheating. If an 

electric heater is turned on by remote control 

while clothing is draped over it, a fire could 

result.

NotE: In order to use your Vizia

TM

 Plug-In Serial 

Interface Module in a Z-Wave

TM

 network, it must 

be Included into the network using a Primary 

Programmer/Remote, such as Leviton’s Cat. 

No., RZCPG. Before Including your module, 

please refer to the Primary Programmer/Remote 

instruction sheet for complete information. Refer 

to Step 3 for further details.

NotE: Use check boxes           when Steps 

are completed.

•  To be installed and/or used in accordance with appropriate electrical codes and regulations.
•  If you are unsure about any part of these instructions, consult a qualified electrician.

•  Save this instruction sheet. It contains important technical data along with testing 

and troubleshooting information which will be useful after installation is complete.

•  RS232 - ASCII
•  Scene capable 
•   Two way communication
•   RF reliability 
•   Ease of installation – No new wiring
•   Compatible with other Z-Wave™ enabled 

devices

NotE: This product requires the use of 

third party software to function, along with a 

relatively high level of programming skill. 

NotES:
•  If using a non-Leviton Programmer/Remote, 

refer to the Programmer/Remote instruction 

sheet.

•  Plug-In Serial Interface Modules included into 

a Z-Wave

TM

 network must be updated after you 

have included all other devices.

a)  If using a Leviton Z-Wave

TM

 Programmer/

Remote, Cat. No. RZCPG, press the Menu 

button and scroll down to System Setup. Press 

the center button to select System Setup Menu. 

Press the center button to select Network. 

Press the center button to <Include Node>.

B)  If using RZCPG Programmer/Remote, you will 

be prompted to prepare device for inclusion. To 

do this you must put the Plug-In Serial Interface 

Module into programming mode. 

C)  To access Program mode, press and hold 

programming button until the LED turns Amber. 

You are now in Programming mode.

 

NotE: If the LED on the Plug-In Serial 

Interface Module turns solid Red while 

including, there has been a communication 

error.

D)  While standing close to the Plug-In Serial 

Interface Module (approximately 2-5 ft.), press 

the center button on the Programmer/Remote 

to <Include> device in the network. NotE: 

Only one device may be included at any time.

E)  The Primary Programmer/Remote will 

assign a Home ID, Node ID, and Name for 

this device.

 

NotE: This information will be stored in the 

Programmer/Remote to be used for future 

reference.

 

NotE: You may name or edit the node of 

this device at this time.

F)  the Plug-In Serial Interface Module is 

now installed in the network.

G)  After all devices are included into the 

network, the Plug-In Serial Interface 

Module must be updated to allow proper 

network function. To update Plug-In Serial 

Interface Module proceed as follows:

 

•   If using a non-Leviton Programmer/

Remote, refer to the Programmer/

Remote instruction sheet for updating 

Plug-In Serial Interface Module.

 

•   If using Leviton Z-Wave

TM

 Programmer/

Remote, Cat. No. RZCPG, press the 

Menu button and scroll down to System 

Setup. Press the center button to select 

  System Setup Menu. Press the center 

button to select Network. Press the 

center button to select Update "cntrl". 

When prompted, press button on the 

Plug-In Serial Interface Module.

 

•   Wait until the RZCPG Programmer/

Remote confirms completion. Update 

is done.

NotE: If the Plug-In Serial Interface Module 

has been successfully Included in the 

network and the user tries to Include it again 

without first excluding it from the network, the 

controller will retain the first node ID it had 

received and ignore the second.

•  Attach RS232 cable to Plug-

In Serial Interface Module 

and CPU.

  oR
  Attach HAI cable to Plug-In 

Serial Interface Module and 

HAI controller.

•  Plug the Plug-in 

Serial Interface 

Module into wall 

receptacle. Verify 

that receptacle is 

live. If controlled 

by a wall switch, 

the switch must 

be kept oN at all 

times.