AeroComm Corporation AC4424-100 Manual Do Utilizador
AC4424 Specifications
AC4424 Specifications
AC4424 Specifications
AC4424 Specifications
12/09/02
12/09/02
12/09/02
12/09/02
20
20
20
20
4.3.8
4.3.8
4.3.8
4.3.8 Write Static Bank #1 Bytes
Write Static Bank #1 Bytes
Write Static Bank #1 Bytes
Write Static Bank #1 Bytes
The Host issues this command to the transceiver to write Static Bank #1 Bytes. Static Bank #1 is a
bank of memory that holds many of the parameters that control the radio. Using the Read/Write Static
Bank #1 command allows these parameters to be changed dynamically. Because the memory bank
is static, when the radio is reset, these parameters will revert back to the settings stored in EEPROM.
Be careful not to change undocumented Static Bank addresses as undesired operation may occur.
bank of memory that holds many of the parameters that control the radio. Using the Read/Write Static
Bank #1 command allows these parameters to be changed dynamically. Because the memory bank
is static, when the radio is reset, these parameters will revert back to the settings stored in EEPROM.
Be careful not to change undocumented Static Bank addresses as undesired operation may occur.
Host Command:
Host Command:
Host Command:
Host Command:
Byte 1 = CCh
Byte 2 = 0Bh
Byte 3 = 00 – FFh corresponding to a valid Static Bank #1 address
Byte 4 = 00 – FFh corresponding to new value for address specified by Byte 3
Byte 2 = 0Bh
Byte 3 = 00 – FFh corresponding to a valid Static Bank #1 address
Byte 4 = 00 – FFh corresponding to new value for address specified by Byte 3
Transceiver Response:
Transceiver Response:
Transceiver Response:
Transceiver Response:
Byte 1 = CCh
Byte 2 = 00 – FFh corresponding to a valid Static Bank #1 address
Byte 3 = 00 – FFh corresponding to new value for address specified by Byte 2
Byte 2 = 00 – FFh corresponding to a valid Static Bank #1 address
Byte 3 = 00 – FFh corresponding to new value for address specified by Byte 2
4.3.9
4.3.9
4.3.9
4.3.9 Read Static Bank #2 Bytes
Read Static Bank #2 Bytes
Read Static Bank #2 Bytes
Read Static Bank #2 Bytes
The Host issues this command to the transceiver to read Static Bank #2 Bytes. Static Bank #2 is a
bank of memory that holds many of the parameters that control the radio. Using the Read/Write Static
Bank #2 command allows these parameters to be changed dynamically. Because the memory bank
is static, when the radio is reset, these parameters will revert back to the settings stored in EEPROM.
Be careful not to change undocumented Static Bank addresses as undesired operation may occur.
bank of memory that holds many of the parameters that control the radio. Using the Read/Write Static
Bank #2 command allows these parameters to be changed dynamically. Because the memory bank
is static, when the radio is reset, these parameters will revert back to the settings stored in EEPROM.
Be careful not to change undocumented Static Bank addresses as undesired operation may occur.
Host Command:
Host Command:
Host Command:
Host Command:
Byte 1 = CCh
Byte 2 = 0Ch
Byte 3 = 00 – FFh corresponding to a valid Static Bank #2 address
Byte 2 = 0Ch
Byte 3 = 00 – FFh corresponding to a valid Static Bank #2 address
Transceiver Response:
Transceiver Response:
Transceiver Response:
Transceiver Response:
Byte 1 = CCh
Byte 2 = 00 – FFh corresponding to a valid Static Bank #2 address
Byte 2 = 00 – FFh corresponding to a valid Static Bank #2 address