Ewig Industries Macao Commercial Offshore Limited 001H22M Manual Do Utilizador
A
E
B
F
C
G
D
SLIDE
SLIDE
(HANG)
(STAND)
°C °F
TX
RF REMOTE SENSOR
RF 433Mhz Wireless Remote Sensor 001H22
A . LCD
Displays temperature and humidity in toggle
B. LED indicator
Flashes when the remote unit transmits a reading
C.
°
C/
°
F slide switch
Selection Centigrade (
°
C) or Fahrenheit (
°
F)
D. T X
Press once to re-transmit manually. Press and hold to clear the TX ID and start re-registration
E. Battery compartment
Accommodates two AAA-size batteries
F. Battery door
G. Removable table stand with wall-mount hole
G. Removable table stand with wall-mount hole
To enable the remote unit on a flat surface and support it in wall-mounting.
During the 3 minutes when the home receiver is seeking for sensor registration signal, remove the bracket stand, and
battery cover. Insert 2 pieces of AAA batteries into the battery compartment according to polarity markings. The channel
1 icon and the temperature/humidity will appear on the LCD of the receiving unit.
battery cover. Insert 2 pieces of AAA batteries into the battery compartment according to polarity markings. The channel
1 icon and the temperature/humidity will appear on the LCD of the receiving unit.
-If the registration is sucessful, a beep confirmation will be heard. If not, check the AAA batteries, repeat the registration
procedure again, or hold the TX button for 2 seconds to send the registration signal. Then, close the battery door.
procedure again, or hold the TX button for 2 seconds to send the registration signal. Then, close the battery door.
-To register sensor 2 and sensor 3: Press and hold the “Channel” button for 2 seconds on the home receiver to select the
channel. Insert batteries for sensor 2, the channel 2 icon and temperature will appear on the LCD of the receiving unit.
Follow the same procedure to register sensor 3.
channel. Insert batteries for sensor 2, the channel 2 icon and temperature will appear on the LCD of the receiving unit.
Follow the same procedure to register sensor 3.
Note:
•
•
The sensor will transmit the registration code automatically once the batteries are inserted. If the batteries have
been already inserted into the battery compartment , hold the TX 2 seconds for registration.
been already inserted into the battery compartment , hold the TX 2 seconds for registration.
•
If the “---” icon appears on the outdoor remote sensor, move the unit closer to the receiving unit. Repeat the
registration procedure again.
registration procedure again.
•
The channels will be automatically assigned to the sensors respectively in sequence of registration.
However, if all sensors are already registered, you can perform the registration again by selecting the desired channel
and hold “Channel” for 2 seconds to enable the receiving unit to receive RF temperature signals.
However, if all sensors are already registered, you can perform the registration again by selecting the desired channel
and hold “Channel” for 2 seconds to enable the receiving unit to receive RF temperature signals.
For wireless remote sensor with detachable probe only
If measurement of water, soil, or other liquid is desired, open the cover of the plug hole at the side of the sensor and
insert the probe plug. (optional)
If measurement of water, soil, or other liquid is desired, open the cover of the plug hole at the side of the sensor and
insert the probe plug. (optional)
Specification
Recommended remote sensor operating range:
Sensor with LCD display
Recommended remote sensor operating range:
Sensor with LCD display
: +32°F to +122°F (0°C to +50°C)
Detachable outdoor probe
: -58°F to +158°F (-50°C to +70°C)
Transmission range
: Maximum 30 meters, open area
Batteries
: AAA size x 2 pcs. (remote sensor)
Battery life
: 6 months
Transmission frequency
: 433.92 MHz
This device could be sensitive to electrostatic discharge, If electrostatic discharge or malfunctioning occurs, please reset this
unit.
unit.
“Modifications not authorized by the manufacturer may void users authority to operate this device”
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must
accept any interference, including interference that may cause undesired operation of the device.
accept any interference, including interference that may cause undesired operation of the device.