Ewig Industries Macao Commercial Offshore Limited 217S53M Manual Do Utilizador
EWIG Model 217 Standard Instruction Manual
During the 3 minutes that the home receiver is seeking for sensor registration signal, remove the bracket
stand, release the screw at the rear of the sensor with a small screwdriver. Remove battery cover. Insert
2pcs AAA batteries into the battery compartment per direction shown. Channel 1 icon and the
temperature will be appear on the LCD of the receiving unit. If not hold the Tx button for 2 seconds on
the sensor to force out sensor registration signal. If registration is successful, close the battery cover and
tighten the screws.
stand, release the screw at the rear of the sensor with a small screwdriver. Remove battery cover. Insert
2pcs AAA batteries into the battery compartment per direction shown. Channel 1 icon and the
temperature will be appear on the LCD of the receiving unit. If not hold the Tx button for 2 seconds on
the sensor to force out sensor registration signal. If registration is successful, close the battery cover and
tighten the screws.
-If registration is sucessful, a beep confirmation tone can be heard. If not, check the condition of the
AAA batteries, repeat the registration procedure again. Close the battery door and back cover and
tighten the screw on the sensor.
AAA batteries, repeat the registration procedure again. Close the battery door and back cover and
tighten the screw on the sensor.
-To register sensor 2 and sensor 3:
Press and hold the “Channel” button for 2 seconds of the home
receiver to trigger sensor registration process. Insert battery for sensor 2, channel 2 icon and tempera-
ture will appear on the LCD of the receiving unit. Follow the same procedure to register sensor 3.
ture will appear on the LCD of the receiving unit. Follow the same procedure to register sensor 3.
Note:
•
•
The sensor will transmit the registration code automatically to complete the registration after the
batteries is just inserted. If the batteries have already inserted into the battery compartment , use a
pen to tap & hold the TX hold 2 seconds for Registration.
pen to tap & hold the TX hold 2 seconds for Registration.
•
If “---” appear on the outdoor chanel, move the sensor closer to the base unit. Repeat the
registration procedure again.
•
The channel number have will be automatically assigned to the respective sensor in sequence of
registration. However, if all 3 RF sensors are already registered, you can perform the registration
again by selecting the desired channel and hold “Channel” 2 seconds to tell the base unit to accept
RF temperature signal, then hold “TX” 2 seconds on the remote sensor.
registration. However, if all 3 RF sensors are already registered, you can perform the registration
again by selecting the desired channel and hold “Channel” 2 seconds to tell the base unit to accept
RF temperature signal, then hold “TX” 2 seconds on the remote sensor.
For wireless remote sensor with attachable probe only
If measurement of water, soil, or other liquid is desired, open the cover of the plug hole at the side of
the sensor and insert the probe plug. (optional)
If measurement of water, soil, or other liquid is desired, open the cover of the plug hole at the side of
the sensor and insert the probe plug. (optional)
071-686173-001900
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment does not cause harmful interference to radio television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures;
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment does not cause harmful interference to radio television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures;
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
Specifications
Recommended remote sensor operating range:
Sensor with LCD display : -20°C to +50°C ( -4°F to +122°F)
Sensor without LCD display : -20°C to +50°C ( -4°F to +122°F)
Detachable outdoor probe : -50°C to +70°C (-58°F to +158°F)
Transmission range : Maximum 30 meter, open area
Batteries : DC 1.5V size AAA x 2 pcs
Recommended remote sensor operating range:
Sensor with LCD display : -20°C to +50°C ( -4°F to +122°F)
Sensor without LCD display : -20°C to +50°C ( -4°F to +122°F)
Detachable outdoor probe : -50°C to +70°C (-58°F to +158°F)
Transmission range : Maximum 30 meter, open area
Batteries : DC 1.5V size AAA x 2 pcs
Battery life (status)
Remote sensor : Typical 6 months
Tranmission frequency : 433.92 Mhz
Remote sensor : Typical 6 months
Tranmission frequency : 433.92 Mhz
Operation is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including interference that
may cause undesired operation of the device.
interference, and (2) this device must accept any interference, including interference that
may cause undesired operation of the device.
This device could be sensitive to electrostatic discharge. If electrostatic discharge or malfunctioning
occurs, please reset this unit.
occurs, please reset this unit.
“Modifications not authorized by the manufacturer may void users authority to operate this device”