Ewig Industries Macao Commercial Offshore Limited MAV220A Manual Do Utilizador
MODEL # MAV219/MAV220 INSTRUCTION MANUAL
Congratulations on your purchase of the new Williams-Sonoma
wireless voice alert grill thermometer. This unit will allow you to see
the temperature of your food cooking in the oven or on the grill from
anywhere in your home. The unit allows you to be alerted by a voice
alert telling you when your food is almost ready or ready and by
beeps that tell the same. The following instructions will show you how
to easily use the thermometer.
THE UNIT HAS A LOCKING CASE. THE TABS WILL HOLD IT CLOSED WHILE
STORED. TO OPEN SIMPLY GRASP THE BATTERY COMPARTMENT OF THE
RECEIVER AND PULL OUT. YOU WILL HEAR A CLICK AND THE UNIT WILL
SEPARATE.
WHEN USED AS A THERMOMETER: First you must register the base unit
with the remote unit (the remote unit has the display showing the
food selections). To register the unit do the following:
● Turn the unit on by holding the MODE button on the receiver unit
until you hear the BEEP sound.
● Plug in the stainless steel probe into the transmitter unit. This
must be done within 120 seconds of turning the unit on.
● The unit should beep three times when turned on and the
probe temperature should appear within 5-10 seconds of
plugging in the probe. When the temperature appears the unit
will beep once.
● If this does not happen repeat the process.
THE PROBE MUST BE PLUGGED INTO THE TRANSMITTER FOR THE UNIT TO
WORK.
ONCE THE UNIT IS ON: Press the MODE button again to change the
unit from the thermometer function to the timer function. This button
will change the feature of timer/thermometer back and forth.
Low battery indicator
for transmitter unit
for transmitter unit
Icon for Meat
Taste level
Meat type
Low battery indicator
for receiver unit
for receiver unit
IF THE SIGNAL IS LOST: If the receiver unit is turned off and then on
and the signal is lost do the following:
● Turn the receiver on by pressing the MODE button for two
seconds.
● Once the unit is on hold the CLEAR button for several seconds
until the probe temperature starts to blink with the --- showing.
● Press and hold the (TX) button inside the battery compartment
of the transmitter or re-plug the temperature probe. This has to
be done within 120 seconds of turning the unit on.
● If the unit registers the transmitter the unit will beep and show
the probe temperature. If it does not register press and hold the
(TX) button again.
HOW TO KNOW IF THE SIGNAL IS LOST: The receiver unit will normally
work within 150 feet of the transmitter. If the receiver is taken out of
range or there is abnormal external interference the receiver may
not be able to receive the transmission from the transmitter. If this
happens the unit will alert you by beeping once for every 3 seconds
to tell you to re-sync the signal. If this happens you need to move the
unit close to the transmitter and follow the instructions above.
SETTING THE SELECTED FOOD TEMPERATURE: The unit is programmed
with selected pre-set temperatures for all types of meats. These
temperatures are recommended by both major cookbooks and the
USDA for food safety.
The chart of the selected temperatures is as follows below:
TO SELECT A SPECIFIC TYPE OF MEAT: Press the button marked “MEAT”
and scroll through the selection until the type of meat (BEEF, VEAL,
CHICKEN, ETC) shows on the LCD (display). There will also be the
meat icon shown on the display.
TO SELECT YOUR OWN PREFERRED TEMPERATURE: Once you have
selected a temperature and food selection – for instance BEEF –RARE
– you can customize the temperature setting by using the HR/▲ sign
to increase the temperature setting or the MIN/▼ to reduce the
temperature setting.
See below examples of what the LCD will look like:
Pre-Alert: When the probe temperature reaches ten degrees to the
set temperature of your food the unit will let you know with the voice
alert “Your food is almost ready” and the unit will beep twice. The
pre-alert will be repeated after four seconds.
Alert: When the probe temperature reaches the set temperature
(selected with the meat and taste selection) the unit will beep three
times and the voice will say “Your food is ready”. At the same time
the alert icon will flash on the face of the unit. To cancel the alert
press the STOP button on the unit.
TO USE THE UNIT AS A TIMER:
● Press the MODE button to switch the unit from Thermometer
setting to Timer setting.
● Press the clear button if the timer is running so that the timer
shows 0:00.
● COUNT UP – To use as a count up timer simply press START. The
timer will count up to a maximum of 23:59:59.
● COUNT DOWN – To use as a count down timer set the hour time
by pressing the HOUR▲ to the proper hour. To set the MINUTE
press the MIN▼ to the desired number of minutes. Once the
hours and minutes are set press start. The unit will count down to
0 and then beep for 20 seconds and the icons will beep.