Chamberlain Group Inc The 1D1519 Manual Do Utilizador

The Receiver DIP switch has three positions labeled “+”, “0” 
and “-”.  The “0” setting cannot be used with the clicker remote.

1) Reset switches: 1 to “-” and positions 2 through 9 to a random
setting using “+” and the “-”. DO NOT USE THE “O” SETTING. 

2) Gather any existing remotes and open to expose the DIP switches. Reset
the DIP switch to match the newly coded receiver. Note: some three button remotes do
not have a #1 switch. Match the 2 through 9 to the receiver. On three button remotes
the large button is now programmed to activate the door. 3) Test all the newly coded
remote controls to be sure that they operate the door before proceeding to the BRAND MODE SETTING.

After determining that the Receiver has a yellow, white or gray
learn button, 1) Gather any existing remotes and open to expose

the DIP switches labeled “+”, “0” and “-”. 2) Reset switches: 1 to 
“-” and positions 2 through 9 to a random setting using “+” and 
the “-”. DO NOT USE THE “0” SETTING, SET ALL REMOTES

TO THE SAME SETTING. On three button remotes the large button is
now programmed to activate the door. 3) The recoded remotes must be
programmed to the receiver. Press and release the smart-learn button.
Then press and hold the existing remote push button for three seconds. 
4) Test all the newly coded remote controls to be sure that they operate the 
door before proceeding to the BRAND MODE SETTING.

With this type receiver, the existing remotes do not contain DIP switches. 
Proceed to BRAND MODE SETTINGS.

LOCK

LIGHT

Motor 
Unit & 
Receiver

Wall Mounted 
Control

Remote Control

The clicker remote can be programmed to operate up to 2 garage door openers or gates,
including different brands.  All programming is done using the:

• Brand switch 
• Transmitter DIP switch 
• Transmit push buttons A and B, and LED indicator

Determine the BRAND of the existing garage door opener or handheld remote controls.  If all
remote controls are lost, the BRAND is located on the ceiling mounted motor unit or on the
receiver near the flexible wire antenna.  Proceed to the SECTION indicated on the BRAND chart
below.

Note: If programming to more than one opener, after programming button “A” refer to brand
chart, and follow the instructions pertaining to the brand you wish to program into button “B”.

When the remotes range is diminished, operation is intermittent, or the LED dims, replace the
battery.  Memory is not lost when the battery is removed.  Note:  Dispose of old batteries
properly.

- 

When LED flashes,
release both buttons.

- 

Press the button you wish to operate the
opener (your choice).

- 

Programming is complete, to test, press the 
button selected to activate garage door.

Match
existing
codes.
Set extra
switches off.

➡

➡

• Open existing remote; determine if there are 9 or 12 code switch settings.

• Set brand mode switches on clicker remote. 

• Program clicker remote push button.

ORANGE/RED
SMART-LEARN BUTTON

• Determine specific brand and circle above.

• Open existing remote to expose code switches.

• Set brand mode switches on clicker remote. 

• Program clicker remote push button.

➡

➡

Determine if your motor unit/receiver system has DIP switches or a smart-learn button.
(Locate the small gray wire antenna.  Some
models require removing the light lens.)

• If the Receiver has 9 DIP switches Proceed to TYPE A
• If the Receiver has a yellow, white, or gray smart-learn button, proceed to TYPE B
• If the Receiver has a green, red, or orange smart-learn button, proceed to TYPE C

SMART-LEARN
BUTTON

➡

DIP SWITCHES

➡

✚

2

3

1

KG

KG

➡

Use this 
button

2

3

1

KG

KG

➡

Remote 
push button

Chamberlain, LiftMaster and Moore-O-Matic are Trademarks of Chamberlain Group. Genie is a Trademark of Overhead Door
Corporation. Linear and Multi-Code are Trademarks of Linear Corporation. Master Mechanic is a Trademark of TruServ. 
Sears is a Trademark of Sears & Roebuck. Stanley is a Trademark of The Stanley Works. 
DoIt is a trademark of DoIt Best Corporation.

©2001, Clicker Corporation

114A2504B

All Rights Reserved    

Printed in Mexico

➡

Match 
existing codes. 
Set extra
switches off.

➡

➡

✚
O

1

2

3

4

5

6

7

8

9

✚
O

1

2

3

4

5

6

7

8

9

Use this 
button

➡

GREEN SMART-LEARN
BUTTON

➡

Code switch
settings are
not used.

➡

➡

Code switch
settings are
not used.

➡

- Stanley, Multi-Code, Linear, Moore-O-Matic

- Genie - 9 Code Switch, Genie - 12 Code Switch

- 

Press and hold both
buttons for 5 seconds
or until LED begins to
flash.

- 

When LED flashes,
release both buttons.

- 

Press the button you wish to operate the
opener (your choice).

- 

Programming is complete, to test, press the 
button selected to activate garage door.

Match
existing
codes.
Set extra
switches off.

➡

➡

- 

Press and hold 
both buttons for 5
seconds or until LED
begins to flash.

- 

Press and hold both buttons for 5 seconds or until LED begins to flash.

- 

When LED flashes, release both buttons.

- 

Press the button you wish to operate the opener (your choice).
For type A & B, proceed to step 6.  For type C, continue on to Step 5.

2

3

1

KG

KG

A. Press and release

Smart-Learn
button.

- 

Programming is complete, to test, press the button selected to activate garage door.

B. Press and hold button 

selected in Step 4 for 3 seconds.

Note: Use pen or small screwdriver 
to move dip switches.

1 2 3 4 5 6 7 8 9

1 2 3 4

➡

➡

10 1112

ON

ON

➡

➡

To prevent possible SERIOUS INJURY or DEATH from a moving gate or garage door:
• ALWAYS keep remote controls out of reach of children. NEVER permit children to operate, or play 

with remote control transmitters.

• Activate gate or door ONLY when it can be seen clearly, is properly adjusted, and there are no 

obstructions to door travel.

• ALWAYS keep gate or garage door in sight until completely closed. Never permit anyone to cross 

path of moving gate or door.

NOTICE: To comply with FCC and or Industry Canada rules, adjustment or modifications of this receiver and/or transmitter are
prohibited, except for changing the code setting or replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.
Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the following two conditions: (1) this device
may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.