Chamberlain Group Inc The 7472 Manual Do Utilizador
2-BUTTON AND 4-BUTTON REMOTE CONTROLS
MODELS 892LT AND 894LT
To prevent possible SERIOUS INJURY or DEATH from a
moving gate or garage door:
• ALWAYS keep remote controls out of reach of children.
moving gate or garage door:
• ALWAYS keep remote controls out of reach of children.
NEVER permit children to operate or play with remote
controls.
controls.
• Activate gate or door ONLY when it can be seen clearly, is
properly adjusted and there are no obstructions to door
travel.
travel.
• ALWAYS keep gate or garage door in sight until completely
closed. NEVER permit anyone to cross path of moving gate
or door.
or door.
PROGRAMMING
Learn
LED
LED
Learn
Button
Button
OR
Learn
LED
LED
Learn
LED
LED
Learn
Button
Button
Learn
Button
Button
OR
LED
Program
Button
Button
A
OPTION A
The instructions are written for garage door openers, however
the steps still apply for compatible products. Make sure the
garage door opener has a working light bulb because it is a
programming indicator. The illustrations are generic, so your
garage door opener may look different.
the steps still apply for compatible products. Make sure the
garage door opener has a working light bulb because it is a
programming indicator. The illustrations are generic, so your
garage door opener may look different.
1
Locate the Learn button on the garage door opener
(Figure 1).
(Figure 1).
2
Remove the battery cover from the new remote control and
locate the Program button (Figure 2).
locate the Program button (Figure 2).
3
To enter programming mode, press the Program button
until the LED on the remote control turns on.
until the LED on the remote control turns on.
4
Press and release the Learn button on the garage door
opener. The Learn LED will light. Within 30 seconds...
opener. The Learn LED will light. Within 30 seconds...
5
Press and release the remote control button that you want
to use...
Check to see if the garage door opener light bulb blinks.
If not, wait for the remote control LED to light solid then
slowly press and release the remote control button again.
Repeat until the light bulb blinks. DO NOT press the button
after the light bulb blinks.
to use...
Check to see if the garage door opener light bulb blinks.
If not, wait for the remote control LED to light solid then
slowly press and release the remote control button again.
Repeat until the light bulb blinks. DO NOT press the button
after the light bulb blinks.
6
To exit programming mode, press and release the Program
button on the remote control. The LED on the remote
control will turn off.
button on the remote control. The LED on the remote
control will turn off.
7
To test, press and release the programmed button on the
remote control. The garage door opener will activate.
remote control. The garage door opener will activate.
1
Make sure the existing dip-switch remote control and the
new remote control are in close proximity to each other.
new remote control are in close proximity to each other.
2
Remove the battery cover from the new remote control and
locate the Program button (Figure 2).
locate the Program button (Figure 2).
3
To enter programming mode on the new remote control,
press the program button until the LED on the remote
control turns on.
press the program button until the LED on the remote
control turns on.
4
Press and hold the button that currently activates your
product on the existing remote control that you want to
copy to the new remote control. The LED on the new remote
control will flash.
product on the existing remote control that you want to
copy to the new remote control. The LED on the new remote
control will flash.
5
Press and release the button on the new remote control that
you want to program. The LED on the new remote control
will flash rapidly, then return to a flash slowly. DO NOT
press the button after the LED flashes.
you want to program. The LED on the new remote control
will flash rapidly, then return to a flash slowly. DO NOT
press the button after the LED flashes.
6
To exit programming mode, press and release the Program
button on the remote control. The LED on the remote
control will turn off.
button on the remote control. The LED on the remote
control will turn off.
7
To test, press and release the programmed button on the
remote control. The gate operator or commercial door
operator will activate.
remote control. The gate operator or commercial door
operator will activate.
MODEL 892LT
MODEL 894LT
FIGURE 1
FIGURE 2
There are two different programming options depending on your application. If you are programming the remote control to an existing DIP switch remote control, refer to OPTION B. For all other
programming, refer to OPTION A.
programming, refer to OPTION A.
The 892LT/894LT remote control is compatible with Security✚ 2.0™ garage door openers, gate operators, commercial door
operators and commercial receivers. The remote control can also be programmed to Security✚ 2.0™ products with encrypted DIP
switches. The remote control can also be used as a replacement for LiftMaster
operators and commercial receivers. The remote control can also be programmed to Security✚ 2.0™ products with encrypted DIP
switches. The remote control can also be used as a replacement for LiftMaster
®
remote control models 972LM/974LM and
372LM/374LM.
B
OPTION B