Adtran BSAP2135 Manual Do Utilizador
4
Support - Phone: 888-423-8726
Quick Start Guide, 61700962F1-13E, June 2018
5
To mount the BSAP 2135 to a horizontal pole:
1.
Place the lock washers, then the flat washers on the four hex cap screws, and drive the screws through
the plane bracket into the back of the case as shown in Figure 4.
the plane bracket into the back of the case as shown in Figure 4.
2. Drive the four round head screws to attach the pole mount base to the plane bracket in a horizontal
position (Figure 8).
3. Thread the open end of the hose strap through the two tabs on the pole mount base (Figure 9).
4. Install the antennas (sold separately) onto the appropriate antenna ports. The antenna ports are
4. Install the antennas (sold separately) onto the appropriate antenna ports. The antenna ports are
labeled 2.4GHz and 5GHz.
5. Wrap the hose strap around the horizontal mounting pole and insert the end into the strap lock.
Tighten the lock of the hose strap to secure the unit to the pole (Figure 11).
8
9
Round Head
Screw
Pole Mount
Base in
Horizontal Position
Base in
Horizontal Position
Hose Strap
Insertion
Insertion
10
11
Vertical
Pole
Mounting
Horizontal Pole
Mounting
S
UPPLYING
P
OWER TO THE
BSAP
The BSAP 2135 does not have a power switch. It is powered when connected to a network device that
supplies PoE based on the IEEE 802.3at standard or an external PoE injector. To power the BSAP
2135, follow these instructions:
Connect the PoE Cable to the BSAP
1.
Disassemble the watertight fitting by unscrewing the cinch nut and pushing the rubber gasket out of the
strain-relief fitting.
strain-relief fitting.
2. Thread the cinch nut onto the customer-provided RJ-45 CAT 5e or CAT 6 cable.
3. Spread the gasket open and wrap it around the cable near the RJ-45 connector.
4. Insert the RJ-45 connector through the strain-relief fitting, and press the gasket back into its
3. Spread the gasket open and wrap it around the cable near the RJ-45 connector.
4. Insert the RJ-45 connector through the strain-relief fitting, and press the gasket back into its
original position.
5. Insert the connector into the RJ-45 receptacle on the bottom of the BSAP.
6. Gently push the strain-relief fitting along the cable until it engages with the black threads, and
6. Gently push the strain-relief fitting along the cable until it engages with the black threads, and
screw it onto the BSAP until it is well seated against the unit.
7. Screw the cinch nut onto the strain-relief fitting until it is well seated against the gasket forming a
watertight seal.
Connect the BSAP to a PoE Source
The BSAP 2135 requires 802.3at PoE. It will not function using 802.3af PoE. The following diagram
illustrates how to provide power to the BSAP 2135 installed outdoors. Three examples are provided:
1.
A PoE switch providing power in conjunction with NetVanta PoE Protector/Injector (1702595F15)
installed indoors.
installed indoors.
2. A non-PoE switch in conjunction with NetVanta PoE Protector/Injector (1702595F15) and an
optional AC Power Adapter (1700501F1) to provide power installed indoors.
3. A third-party outdoor rated 802.3at PoE injector (PowerDsine PD-9001GO) or equivalent with
GR-1089-Core Criteria B Surge Protection installed outdoors with mesh.
For outdoor applications, the watertight fitting must be used when
connecting PoE cables to the BSAP 2135. Failure to use the watertight
fitting when the unit is installed outdoors will void the user's warranty and
could create a fire or shock hazard.
5GHz
5GHz
Cinch Nut
Gasket
Strain-relief
Fitting
Fitting
Antenna
Connectors
RJ-45 Receptacle
and Connector
and Connector