Adtran TRACERT1L7 Manual Do Utilizador
61280.003L1-1B
P
AGE
33
4/12/99
M
AIN
M
ENU
S
ELECTIONS
S
YSTEM
S
TATUS
P
AGE
This page displays the status of major system components. This
is a status screen only; no configurations can be performed. More
detailed information can be obtained by way of the Main Menu.
is a status screen only; no configurations can be performed. More
detailed information can be obtained by way of the Main Menu.
Current System Status
Elapsed Time 00:14:59
____ ADTRAN Technical Support - 800/726-8663 ____
T1A ===| |-------------------[RF UP]-------------------->| |=== T1A
| | | |
T1B ===| |<------------------[RF UP]---------------------| |=== T1B
---- ----
Local Tracer Remote Tracer
Freq Plan A Freq Plan B
____ ADTRAN Technical Support - 800/726-8663 ____
T1A ===| |-------------------[RF UP]-------------------->| |=== T1A
| | | |
T1B ===| |<------------------[RF UP]---------------------| |=== T1B
---- ----
Local Tracer Remote Tracer
Freq Plan A Freq Plan B
Tx Pwr Rx Pwr Tx Pwr Rx Pwr
+20dBm[X] [X] Nominal +20dBm[X] [X] Nominal
[X] [X] [X] [X]
[X] [X] Site: ADTRAN [X] [X]
[X] [X] [X] [X]
[X] [X] Code Sync: Yes [X] [X]
[X] [X] Carrier Sync: Yes [X] [X]
[X] [X] T1 Mux Sync: Yes [X] [X]
[X] [X] Chipping Code: 9 [X] [X]
[X] [X] [X] [X]
[X] [X] [X] [X]
-15dXm[X] [X] Minimum -15dBm[X] [X] Minimum
=======================================================================
Press ‘m’ for Main Menu:
+20dBm[X] [X] Nominal +20dBm[X] [X] Nominal
[X] [X] [X] [X]
[X] [X] Site: ADTRAN [X] [X]
[X] [X] [X] [X]
[X] [X] Code Sync: Yes [X] [X]
[X] [X] Carrier Sync: Yes [X] [X]
[X] [X] T1 Mux Sync: Yes [X] [X]
[X] [X] Chipping Code: 9 [X] [X]
[X] [X] [X] [X]
[X] [X] [X] [X]
-15dXm[X] [X] Minimum -15dBm[X] [X] Minimum
=======================================================================
Press ‘m’ for Main Menu:
Figure 3-1. System Status Page
The upper portion of the screen indicates how long the system
has been running since the last reset operation. The “T1A” and
“T1B” labels will be highlighted if any error conditions exist on
that T1 interface.
has been running since the last reset operation. The “T1A” and
“T1B” labels will be highlighted if any error conditions exist on
that T1 interface.
The status of the radio link is indicated as Up or Down. The left
portion of the screen reports the status of the local system (the
system to which the terminal is attached); the right portion reports
the status of the remote system. The approximate transmitter
and receiver signal levels are shown via the “fuel gauges.” If the
link is down and remote end data is unavailable, the fuel gauges
will show “-” instead of “x.” The Code Sync, Carrier Sync, and T1
Mux Sync will all be “yes” for an operational link. Chipping code
indicates the code to which the system is set. At any point in the
VT-100 menu structure, pressing the Escape key will bring the
operator back to this screen.
portion of the screen reports the status of the local system (the
system to which the terminal is attached); the right portion reports
the status of the remote system. The approximate transmitter
and receiver signal levels are shown via the “fuel gauges.” If the
link is down and remote end data is unavailable, the fuel gauges
will show “-” instead of “x.” The Code Sync, Carrier Sync, and T1
Mux Sync will all be “yes” for an operational link. Chipping code
indicates the code to which the system is set. At any point in the
VT-100 menu structure, pressing the Escape key will bring the
operator back to this screen.
O
PERATION