Murata Electronics North America 910M Manual Do Utilizador
WIT910
Enable Global Network Mode
For networks with multiple base stations, remotes are ordinarily only able to link to one
base station, set by the hopping pattern. Mode 1 enables the global mode that allows
remotes to link to any base station they can hear, acquiring whatever hop pattern is
required. In this mode a remote can only change base stations once it is no longer
registered with a base station.
Set Lockout Key
Allows further network segregation beyond the network number. This feature allows
multiple co-located networks in which global roaming or seamless roaming is enabled. In
global and seamless roaming, a remote is allowed to link to any base regardless of the
network number as long as the lockout key agrees. By using different lockout keys, the
bases to which remotes link can be limited or segregated.
Set Hopping Pattern
The WIT910 has 64 preprogrammed hopping patterns (also referred to as network
numbers). By using different hopping patterns, nearby or co-located networks can avoid
interfering with each other’s transmissions. Even if both networks tried to use the same
frequency, on the next hop they would be at different frequencies.
Set Transmit Power
The WIT910 has two preset transmit power levels, 10mW (10dBm), 100mW (20dBm)
and 500mW (27dBm). Control of the transmit power is provided through this command.
Default is 100mW.
Read Receive Signal Strength Indicator (RSSI)
This command reports the relative signal strength averaged over the last 10 hops. This
command returns a one byte value that is proportional to received signal strength and can
range from
For networks with multiple base stations, remotes are ordinarily only able to link to one
base station, set by the hopping pattern. Mode 1 enables the global mode that allows
remotes to link to any base station they can hear, acquiring whatever hop pattern is
required. In this mode a remote can only change base stations once it is no longer
registered with a base station.
Set Lockout Key
Allows further network segregation beyond the network number. This feature allows
multiple co-located networks in which global roaming or seamless roaming is enabled. In
global and seamless roaming, a remote is allowed to link to any base regardless of the
network number as long as the lockout key agrees. By using different lockout keys, the
bases to which remotes link can be limited or segregated.
Set Hopping Pattern
The WIT910 has 64 preprogrammed hopping patterns (also referred to as network
numbers). By using different hopping patterns, nearby or co-located networks can avoid
interfering with each other’s transmissions. Even if both networks tried to use the same
frequency, on the next hop they would be at different frequencies.
Set Transmit Power
The WIT910 has two preset transmit power levels, 10mW (10dBm), 100mW (20dBm)
and 500mW (27dBm). Control of the transmit power is provided through this command.
Default is 100mW.
Read Receive Signal Strength Indicator (RSSI)
This command reports the relative signal strength averaged over the last 10 hops. This
command returns a one byte value that is proportional to received signal strength and can
range from
00H
to
FFH
. Typical values range from
30H
to
80H
where the lower the
number the lower the received signal strength and the higher the number the higher the
received signal strength. This is a relative indication and does not directly correspond to
a field strength number. This is available only at the remotes as the base station is the
only source that transmits on a regular basis. Plus, in a point-to-multipoint network the
base will receive different signal strengths from each remote.
Set Point-to-Point Direct Mode
Sets point-to-point mode that is recommended for point-to-point applications, especially
where the remote radio is mobile and may leave and re-enter the range of the base. This
mode fixes the remote handle assignment to always be
received signal strength. This is a relative indication and does not directly correspond to
a field strength number. This is available only at the remotes as the base station is the
only source that transmits on a regular basis. Plus, in a point-to-multipoint network the
base will receive different signal strengths from each remote.
Set Point-to-Point Direct Mode
Sets point-to-point mode that is recommended for point-to-point applications, especially
where the remote radio is mobile and may leave and re-enter the range of the base. This
mode fixes the remote handle assignment to always be
30H
and improves the re-
registration process. The point-to-point mode must be set in both base and remote radios.
© 2000- 2004 Cirronet™ Inc
22
M-0910-0000 Rev -