Murata Electronics North America 2832 Manual Do Utilizador
Copyright © Murata Manufacturing Co., Ltd. All rights reserved. October 2017
MBN52832 Data Sheet, v1.1, 06/14/2018
MBN52832 Data Sheet, v1.1, 06/14/2018
Page 29 of 34
www.murata.com
• Is connected.
• Consult the dealer or an experienced radio/TV technician for help.
12.2 FCC Labeling Requirements
When integrating the MBN52832 into a product the FCC labeling requirements must be met. This includes a clearly visible
label on the outside of the finished product specifying the MBN52832 FCC identifier (FCC ID: HSW2832) as well as the
notice above. The exterior label can use wording such as “Contains Transmitter Module FCC ID: HSW2832” or “Contains
FCC ID: HSW2832” although any similar wording that expresses the same meaning may be used.
label on the outside of the finished product specifying the MBN52832 FCC identifier (FCC ID: HSW2832) as well as the
notice above. The exterior label can use wording such as “Contains Transmitter Module FCC ID: HSW2832” or “Contains
FCC ID: HSW2832” although any similar wording that expresses the same meaning may be used.
12.3 IC Notice (Canada)
The term “IC” before the certification/registration number only signifies that the Industry Canada technical specifications
were met.
Le terme “IC” devant le numéro de certification /d’enregistrement signifie seulement que les spécifications techniques
Industrie Canada ont été respectées.
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to
The following two conditions: (1) this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the device.
Cet appareil est conforme avec Industrie Canada RSS standard exempts de licence (s). Son utilisation est soumise à Les
deux conditions suivantes: (1) cet appareil ne peut pas provoquer d'interférences et (2) cet appareil doit accepter Toute
interférence, y compris les interférences qui peuvent causer un mauvais fonctionnement du dispositif.
This device complies with Health Canada’s Safety Code 6 / IC RSS-210. The installer of this device should ensure that
RF radiation is not emitted in excess of the Health Canada’s requirement. Information can be obtained at:
were met.
Le terme “IC” devant le numéro de certification /d’enregistrement signifie seulement que les spécifications techniques
Industrie Canada ont été respectées.
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to
The following two conditions: (1) this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the device.
Cet appareil est conforme avec Industrie Canada RSS standard exempts de licence (s). Son utilisation est soumise à Les
deux conditions suivantes: (1) cet appareil ne peut pas provoquer d'interférences et (2) cet appareil doit accepter Toute
interférence, y compris les interférences qui peuvent causer un mauvais fonctionnement du dispositif.
This device complies with Health Canada’s Safety Code 6 / IC RSS-210. The installer of this device should ensure that
RF radiation is not emitted in excess of the Health Canada’s requirement. Information can be obtained at:
Cet appareil est conforme avec Santé Canada Code de sécurité 6 / IC RSS-210. Le programme d'installation de cet
appareil doit s'assurer que les rayonnements RF n'est pas émis au-delà de l'exigence de Santé Canada. Les informations
peuvent être obtenues:
This radio transmitter MBN52832 has been approved by Industry Canada to operate with the antenna types listed below
with the maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the
maximum gain indicated for that type, are strictly prohibited for use with this device.
Le présent émetteur radio (identifier le dispositif par son numéro de certification ou son numéro de modèle s'il fait partie
du matériel de catégorie I) a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés ci-
dessous et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne
non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour
l'exploitation de l'émetteur.
Table 12.3 External Antenna to comply with IC
Part Number
Vendor
Gain (dBi)
Type
Connector
Remarks
S2406PL
Cushcraft
6.0
Patch
U.FL
Necessary for FCC/IC
compliance only.
compliance only.
HG2407RD-RSP
L-Comm
7.0
Dipole
U.FL
Necessary for FCC/IC
compliance only.
compliance only.