A Plus Info Corp AS1795 Manual Do Utilizador

  This device has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses, and can radiate
radio frequency energy. If not installed in accordance with the instructions
in this manual, harmful interference to radio communication may occur.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause interference to radio
and television reception, which can be determined by turning the equipment
off and on, the user is encouraged to correct the interference by one or more
of the following measures:

l  Re-orient or relocate the receiving antenna.
l  Increase the space between the equipment and receiver.
l  Connect the equipment into an outlet on a circuit different from the

one that the receiver is connected.

l  Consult the dealer or an experienced radio/TV technician for

help.

l  Use only RF shielded cable to connect this monitor to a computer

device.

1.  Shut down and power off computer. Connect the 15-pin video signal

cable to the appropriate socket on the PC, and lock attached screws to
ensure proper connection between monitor and PC system. Connect
power cord to monitor. Connect the other end of power cord to
appropriate power source – for plugable equipment the Socket-Outlet
shall be installed near the Monitor and shall be easily accessible.

2.  Power up computer. The monitor simultaneously auto detects the

frequency of the input video signal and display the picture.

3.  Use the main control knob to adjust the display:

l  Press the control knob once to bring up the On-Screen-Display

menu in “selecting mode”.

l  In selecting mode, rotate the control knob clockwise or counter-

clockwise to select feature for adjustment. The selected icon is
displayed in red and all others in white. Press the control knob once
to enter “adjusting mode”, the “%” mark starts blinking.

l  In adjusting mode, rotate the control knob clockwise or counter-

clockwise to adjust the selected feature. Press the control knob once
again to return to selecting mode, the “%” mark stops blinking.

l  If the control knob is not operated for more than 10 seconds, the

display will save the adjusted settings and turn the On-Screen-
Display menu off.

4.  If horizontal or vertical frequency is out of the operating range as

specified in the specification, the display enters power saving mode
and the power indicator blinks. If both are out of range, the display
turns off and power LED is extinguished.

5.  Press the power saving button (beside the main control knob) to force

the display into power saving mode and power indicator off. Press the
power saving button again to resume operation.

ICON Display Feature (page 1) ICON Display Feature (page 2)

Save seting and escape

Degauss function

Vertical Size

Vertical morie

Vertical Position

Horizontal morie

Horizontal Size

Vertical dynamic focus

Horizontal Phase

Horizontal dynamic focus

Trapezoid

9300°K color temerpture

Pincushion

6500°K color temperture

Parallelogram

Red video gain control

Pin-Balance

Green video gain control

Vertical S correction

Blue video gain control

Vertical C correction

Recall factory function

Horizontal linearity

Red Bias adjustment

Cornor correction

Green Bias adjustment

Recall factory function

Blue Bias adjustment

Tilt control

Select input level 0.7/1.0V

Next page

Next page

Brightness

Vertical OSD position

Contrast

Horizontal OSD position

CRT

Size & Dot Pitch

17” - 0.26 / 0.28mm

Face Treatment

Non-glare

Deflection Angle

90

°

Display

Factory setting

300x225mm (11.8x8.86”)

Size

Over Scan

325x244mm (12.8x9.61”)

Display

Horizontal Freq.

30~95Khz

30~70Khz

Format

Vertical Freq.

50~160Hz

50~125Hz

Max. Resolution

(N.I.)

1600x1200

1280x1024

Bandwidth

150Mhz

Memories

26 Sets

20 Sets

Input

Connectivity

Enhanced VESA standards, MAC II

Signal

Video Signal

RGB Analog 0.7 or 1.0 Vp-p

Connector

15 Pin D-shell

Input Voltage

100~240Vac, 50/60Hz

Consumption

110W

85W

Sleep Mode

10W

Deep Sleep Mode  1W

Power

PFC

Option

Mechanical Dimension(HxWxD) 420x410x440mm (16.5x16.1x17.3”)

Specs

Packing(HxWxD)

537x527x575mm (21.1x20.7x22.6”)

Adjustment

Tilt and Swivel

External

Control

On Screen Display Contrast, Brightness, V-Size, V-Position, H-

Size, H-Phase, Trapezoid, Pincushion,

Parallelogram, Pin-Balance, H-Linearity,

S/C/Cornor, Tilt, Degauss, H/V Morie,

Red/Green/Blue Intensity, Input Level,

Red/Green/Blue Bias Intensity, 9300/6500,

Horizontal/Vertical Dynamic Focus

Plug & Play Windows 98

compliant

DDC1 / 2B

Speaker

External

Optional

Pin

Assignment

Pin 1:R

Pin 6:Gnd

Pin11:Gnd

Pin 2:G

Pin 7:Gnd

n 12:SDA

Pin 3:B

Pin 8:Gnd

Pin 13:H-sync

Pin 4:Gnd Pin 9:+5V

Pin 14:V-sync

Pin 10:Gnd Pin 15:SCL