FLIR Commercial Systems Inc. EX845 Manual Do Utilizador
11
Data Hold
To freeze the LCD reading, press the HOLD button. While data hold is active, the HOLD icon appears on the
LCD. Press the HOLD button again to return to normal operation.
LCD. Press the HOLD button again to return to normal operation.
Peak Hold
The Peak Hold function captures the peak AC or DC voltage or current. The meter can capture negative or
positive peaks as fast as 1 millisecond in duration.
positive peaks as fast as 1 millisecond in duration.
1.
Turn the function switch to the A or V position.
2. Use
the
MODE button to select AC or DC .
3.
Allow time for the display to stabilize.
4.
Press and Hold the PEAK button until “CAL” appears in the display. This procedure will zero the range
selected.
5. Press
the
PEAK button, Pmax will display.
6.
The display will update each time a higher positive peak occurs.
7. Press
the
PEAK button again, Pmin will display. The display will now update and indicate the lowest
negative peak.
8.
To return to normal operation, press and hold the PEAK button until the Pmin or Pmax indicator
switches off.
Note: If the Function switch position is changed after a calibration the Peak Hold calibration must be
repeated for the new function selected.
repeated for the new function selected.
MAX/MIN
1. Press
the
MAX/MIN key to activate the MAX/MIN recording mode. The display icon "MAX" will appear.
The meter will display and hold the maximum reading and will update only when a new “max” occurs.
2. Press
the
MAX/MIN key and “MIN” will appear The display icon "MIN" will appear. The meter will display
and hold the minimum reading and will update only when a new “min” occurs
3. Press
the
MAX/MIN key and a blinking “MAX MIN” will appear. The meter will display the present
reading, but will continue to update and store the max and min readings.
4.
To exit MAX/MIN mode press and hold the MAX/MIN key for 2 seconds.
Temperature Units (˚F / ˚C)
The temperature units selection switch is located in the battery
compartment.
To change the units, remove the battery door, lift out the battery
and set the
switch for the desired units.
LCD Backlight Button
The LCD is equipped with backlighting for easier viewing,
especially in
dimly lit areas. Press the backlight button to turn the backlight on.
Press again to
turn the backlight off.
Bluetooth enable/disabled and store trigger
1 、Long pres s 2 seconds Bluetooth enable, LCD display Bluetooth symbol, again long by 2 seconds
Bluetooth disabled, LCD Bluetooth symbol disappears.
2、And with the Bluetooth-enabled devices like the primary, the short press switch trigger signal is stored,
once again short the switch, cancel trigger stored signal,
2、And with the Bluetooth-enabled devices like the primary, the short press switch trigger signal is stored,
once again short the switch, cancel trigger stored signal,
Automatic Power OFF
In order to conserve battery life, the meter will automatically turn off after approximately 25 minutes. To turn
the meter on again, turn the function switch to the OFF position and then to the desired function position.
the meter on again, turn the function switch to the OFF position and then to the desired function position.
Maintenance
WARNING: To avoid electrical shock, disconnect the meter from any circuit, remove the test leads from the
input terminals, and turn OFF the meter before opening the case. Do not operate the meter with an open
case.
input terminals, and turn OFF the meter before opening the case. Do not operate the meter with an open
case.
Cleaning and Storage
Periodically wipe the case with a damp cloth and mild detergent; do not use abrasives or
solvents. If the meter is not to be used for 60 days or more, remove the battery and store it separately.
solvents. If the meter is not to be used for 60 days or more, remove the battery and store it separately.
Battery Replacement
1.
Remove the Phillips head screw that secures the rear battery door
2.
Open the battery compartment
3.
Replace the 9V battery
4.
Secure the battery compartment
Units Switch
F
C