Mascot Electric Co. Ltd. GT-3 Manual Do Utilizador
WIRELESS
WIRELESS NOTE
1
FEATURES & SPECIFICATIONS
WIRELESS
12
FCC Statement
This device complies with part 15 of the FCC rules. Operation is subject to the following two
conditions: (1)This device may not cause harmful interference and (2) This device must
accept any interference received, including interference that may cause undesired operation
conditions: (1)This device may not cause harmful interference and (2) This device must
accept any interference received, including interference that may cause undesired operation
Notice : The changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
compliance could void the user’s authority to operate the equipment.
IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no
change to the antenna or the device is permitted. Any change to the antenna or the device
could result in the device exceeding the RF exposure requirements and void user’s authority
to operate the device.
change to the antenna or the device is permitted. Any change to the antenna or the device
could result in the device exceeding the RF exposure requirements and void user’s authority
to operate the device.
1. Introduction
Thank you for purchasing our product. This PLL synthesized wireless microphone system
operates in UHF band frequency with 15 or 16 selectable channels. Please read this
instruction manual carefully before operating the system. This manual covers the function
and operation of the wireless microphone system.
operates in UHF band frequency with 15 or 16 selectable channels. Please read this
instruction manual carefully before operating the system. This manual covers the function
and operation of the wireless microphone system.
2. Safety
Do not spill liquid on the appliance and do not drop it on a hard concrete floor.
Do not place the appliance near heat sources such as radiators, amplifier, or etc.
Do not expose it to direct sunlight, extremely dust, excessive moisture, or vibration.
Take out the battery from transmitter, if the appliance has been not used for a longer
Do not place the appliance near heat sources such as radiators, amplifier, or etc.
Do not expose it to direct sunlight, extremely dust, excessive moisture, or vibration.
Take out the battery from transmitter, if the appliance has been not used for a longer
period. This will avoid the damage resulting from a defective leaking battery.
3. Environment
Do not throw used batteries into a fire or garbage bin with domestic rubbish. Be sure to
dispose of used batteries in accordance with local waste disposal rules.
When disposing the equipment, remove the batteries, separate the case, circuit boards,
and cables, and dispose of all components in accordance with local waste disposal rules.
4. Wireless Note
Before setting up, make sure that the transmitter and receiver are tuned to the same
frequency.
Do not use two transmitters in the same frequency.
Use good quality batteries to avoid the damage resulting from a defective leaking battery.
Turn the MIC/LINE switch on the rear of receiver to adjust receiver output level to match
Use good quality batteries to avoid the damage resulting from a defective leaking battery.
Turn the MIC/LINE switch on the rear of receiver to adjust receiver output level to match
input level requirements of an audio mixer or amplifier.
While checking sound, move the transmitter around the area where you use the system to
look for dead spots. If you find any dead spot, change the receiver position. If it does
not work, avoid such places.
not work, avoid such places.
To avoid interference, do not put the receiver too near metal object and avoid obstructions
between transmitter and receiver.
Avoid the interference from TV, radio, other wireless appliances and etc.
9. System Feature
Operating in UHF band frequency with synthesizer controlled.
The wireless microphone system with 16 selectable frequencies via Phase Locked Loop (PLL)
The wireless microphone system with 16 selectable frequencies via Phase Locked Loop (PLL)
circuitry makes it easy to choose non-interfered channels.
Diversity with two antennas to ensure the reception quality.
Super high sensitivity, extremely low noise transmission and reception.
SMT assembled PCB module ensures the quality and stability.
Super high sensitivity, extremely low noise transmission and reception.
SMT assembled PCB module ensures the quality and stability.
10. System Specification
Receiver
Carrier Frequency Range
: UHF band
Frequency Stability
:
±0.005%
Receiving Sensitivity
: At 8 dBμV over 80dB S/N ratio
Image and Spurious Rejection : 80 dB minimum
Selectivity
Selectivity
: ＞50dB
Modulation Mode
: FM
IF Frequency
: 1
st
: 56MHz; 2
nd
: 10.7MHz
Tone Signal
: 32.768KHz
S/N ratio
: ＞94dB, at 48KHz deviation and 60dB
µV antenna input
AF Response
: 80Hz to 12KHz (
±3dB)
T.H.D.
: Less than1.0% (at 1KHz)
Power Supply
: DC 12V ~ 18V
Audio Output
: Balanced and unbalanced outputs for Single channel /
Switching diversity
(Mic.=-20dB / Line = 0dB)
Switching diversity
(Mic.=-20dB / Line = 0dB)
Current consumption
: 150mA (Max.) A
Handheld/Bodypack Transmitter
Carrier Frequency Range
: UHF band
RF Power Output
: 10mW (max.)
Oscillation Mode
: PLL synthesized, 16Channel selectable
Frequency Stability
:
±0.005%
Maximum Deviation
:
±48KHz with limiting compressor
Spurious Emission
: ＞60dB below carrier frequency
T.H.D.
: ＜1% (at 1KHz)
Microphone Capsule
: Handheld: uni-directional dynamic or uni-directional
electret condenser unit
Lavalier: uni-directional electret condenser unit
Tone Signal
: 32.768KHz
Battery
: DC3V (2 x 1.5V AA size batteries ) or
DC 2.4V ( 2 x 1.2V AA size rechargeable batteries)
Current consumption
: 110mA at 3V
DESIGN AND SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE.