Lutron Electronics Company Inc 0119 Manual Do Utilizador

OFF

ON

Hold for 6 seconds  

until LEDs start 

blinking

—

and thank you for purchasing a Caséta 

Wireless in-wall fan control. In order to control your 
ceiling fan from an app or remote, you’ll need to replace 
an existing switch with a Caséta Wireless in-wall fan 
control.

Before you install the fan control, please read quick-start 
guide and watch the installation video at

  

www.casetawireless.com/support
We hope you enjoy the convenience of Caséta Wireless!

1.    Use to control one paddle-type ceiling fan 

(permanent split-capacitor). 

2.   Use the ceiling fan’s pull chain to set its speed to 

the highest setting. 

3.   Do not use to control fans that use shaded-pole 

motors (i.e. bath exhaust fans). 

4.   Do not use to control fans that have integrated 

fan speed controls (i.e. fans that have a remote 

control), unless the integrated control is removed 

from the ceiling fan. 

5.   Do not connect to any other motor-operated 

appliance or to any lighting load type. 

6.   Do not use to control a fan lighting load (i.e.  

light kit).

7.  Do not use to control DC motor fans.

Fan—up to 1.5 A

In-wall fan control 
(PD-FSQN)

Works with one paddle-

type ceiling fan:

Flat-head screwdriver

Wire connectors (3)

Phillips-head screwdriver

Pliers

Screws (2)

Installation for 

ceiling fans

 with one wall switch (single pole)

Some fans have one wall switch, while others 
have two or more wall switches. We’ve included 
instructions for fans with one wall switch (called a 
single pole). If your fan has more than one switch 
(called a 3-way), 

please visit  

 for complete 

installation instructions and how-to videos.

May result in serious injury or death. Turn off 
power at circuit breaker or fuse before installing.

Remove the wallplate from switch.

Install the fan according to the manufacturer’s 
instructions and ensure proper operation. 

Set the fan to the highest speed using the pull chains. 

Remove the switch and pull it away from the wall.

*  If your switch has more than 3 wires attached, see 

“Installing Caséta Wireless in a 3-way switch application” 
video at 

Bend back 
and forth.

Tag

Ground

Ground

Ground

Place tag on load wire.

 Disconnect all three 

wires* from the switch.

Connect the bare copper (or green) “ground” wire 
from the wallbox to the green wire on the 

fan control 

using a wire connector.

2  Wrap line/hot wire around screw terminal. Tighten 

securely to 5 in-lb (0.55 N•m)

3  Connect the neutral wire from the wallbox to the 

white wire on the fan control using a wire connector.

4  Connect the load wire from the wallbox to the yellow 

wire on the fan control using a wire connector.

Do not remove outside side sections 
on the controls at the end of gang

.

Each control 
has inside side 
sections removed.

Control at middle has all 
side sections removed.

Attach the adapter to the fan control using the  
screws provided and snap on the wallplate.

(If you installed the control next to other dimmers, 
switches, or controls, you’ll need to install a wallplate 
with the correct size/number of openings to 
accommodate all the devices)

Use the screws provided.

Pairing the fan speed control 

and Pico remote control

Go to 

www.casetawireless.com/support for 

additional troubleshooting suggestions.

Fan does not 
turn ON and no 
indicator lights 
turn ON

.

•  Ensure Front Accessible 

Service Switch (FASS) is fully 
pushed in to the ON position.

•  

Ensure that the fan pull chain is 
set to highest possible setting

.

•  Neutral wire is not connected.  

Check wiring.

•  Breaker is OFF or tripped (or 

fuse blown). Reset breaker 
or replace fuse. If condition 
persists, contact Lutron 
Customer Assistance or a 
licensed electrician.

•  Load and Line wires possibly 

reversed, refer to wiring 
diagram in step 6.

Fan does not 
work.

Fan direction switch is between 
forward and reverse. Set switch 
to desired position.

Fan vibrates or 
wobbles.

•  

Fan direction switch is between 
forward and reverse. Set switch 
to desired position.

•  Fan blades must be balanced. 

See fan manufacturers 
installation guide to balance 
fan.

Fan speed is too 
slow.

Set fan pull chain speed to high.

Love Caséta Wireless controls?

 Have ideas 

for making them better? Tell us what you think 
and we’ll extend your warranty by 1 year. 
www.casetawireless.com/register

For advanced features, tips for using Caséta Wireless products, the complete Caséta Wireless product line, and more, 
please visit 

Changing the favorite fan speed 

setting on the Pico remote 

control or fan control

 (sold 

You can use the round “favorite” 
button on the Pico remote control 
or fan control to recall a favorite 
fan speed setting. We’ve set it to 
Medium, but you can change it to 
any speed you like.

Favorite

Use only with permanently installed ceiling fans. 

To 

avoid overheating and possible damage to other 
equipment, do not use to control receptacles, motor-
driven appliances, or transformer-supplied appliances.

Install in accordance with all national and local  
electrical codes.

When no “grounding means” exist in wallbox, the 
National Electrical Code (NEC

®

) allows a control to 

be installed as a replacement if 1) a nonmetallic, 
noncombustible faceplate is used with nonmetallic 
attachment screws or 2) the circuit is protected by a 
ground fault circuit interrupter (GFCI). When installing 
a control according to these methods, cap or remove 
green wire before screwing control into wallbox.

This device complies with part 15 of the FCC Rules and Industry Canada 
license-exempt RSS standard(s). Operation is subject to the following two 
conditions: (1) This device may not cause interference, and (2) this device 
must accept any interference, including interference that may cause undesired 
operation. Modifications not expressly approved by Lutron Electronics Co., 
Inc. could void the user’s authority to operate this equipment.
Note: This equipment has been tested and found to comply with the limits for 
a Class B digital device, pursuant to part 15 of the FCC Rules. These limits 
are designed to provide reasonable protection against harmful interference 
in a residential installation. This equipment generates, uses and can radiate 
radio frequency energy and, if not installed and used in accordance with 
the instructions, may cause harmful interference to radio communications. 
However, there is no guarantee that interference will not occur in a particular 
installation. If this equipment does cause harmful interference to radio or 
television reception, which can be determined by turning the equipment off 
and on, the user is encouraged to try to correct the interference by one or 
more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which 

the receiver is connected.

—Consult the dealer or an experienced radio/TV technician for help.

)Lutron Lutron, Caséta and Pico are trademarks of Lutron Electronics 

Co., Inc., registered in the U.S. and other countries. FASS and 
Smart Bridge are trademarks of Lutron Electronics Co., Inc. NEC is a 
registered trademark of the National Fire Protection Association, Quincy, 
Massachusetts. Google and the Google logo are registered trademarks of 
Google Inc., used with permission.
© 2018 Lutron Electronics Co., Inc

                                                                             P/N 0301907  REV A

Lutron Electronics Co., Inc.  

7200 Suter Road 

Coopersburg, PA  18036-1299, U.S.A. 

Hold the favorite button on 

either the remote or control 

for 6 seconds until LEDs 

blink twice on in-wall fan 

control. New favorite level is 

now saved.

Important note:

Hold for 6 seconds  

until fan control LEDs 

flash 3 times.

In-wall fan control
PD-FSQN

120 V~  50/60 Hz

1.5 A

Important notes:

1. For indoor use only. 
2. Operate between 32 ˚F (0 ˚C) and 104 ˚F (40 ˚C).

Repeat steps to pair other  
Pico remote controls.

Wireless

Pico remote control (sold separately)

On

Off

Slower

Faster 
Favorite

 

FASS 
Front Accessible 
Service Switch

In-wall fan  
control

On

Off

Slower

Favorite

Faster

With a smartphone or tablet (Bridge required, sold separately)

The Lutron app will walk you through 

setting up your devices.

Lutron

The Caséta Wireless fan control can be controlled from a 
smartphone when used with the Lutron Smart Bridge.
 If you are using the fan control and remote control with the Lutron 
Smart Bridge follow the instructions below.

Search for “Lutron Caseta”

Lutron

Lutron Smart Bridge

Note: 

If you are using the fan control and remote control with 

another manufacturer’s bridge, please refer to that manufacturer’s 
instructions for set-up.

Lutron

Lutron app

Apple is a trademark of Apple Inc., registered in the U.S. and other countries. App Store is a service mark of Apple Inc.

Without a smartphone or tablet (Bridge not required)

Warranty
For warranty information, please visit  
www.casetawireless.com/warranty

P/N 0301907  REV A

Control  

three ways

  Add devices 

• Pico remotes

• Dimmers 

• Shades

• Switches

• Fan controls 

Schedule  

your lights, 

fans, or loads

Connect  

while away

Tag

Tag

Using your controls