HID Global Corporation 5553 Manual Do Utilizador
HF Multi ISO RFID Reader User Manual, Firmware V1.4
1508-USM-00-0-04
2.2.15 Selection Time-Out ISO 14443A (17h)
The default value is 10h. (~4.8mS)
The Selection Time-out represents the reader card communication time-out for the select, high-
speed select, continuous read, multi-list, multi-select and MIFARE login command with ISO
14443A tags. Use low values for a better reaction time between the card and the reader. One time
slice is around 300us.
speed select, continuous read, multi-list, multi-select and MIFARE login command with ISO
14443A tags. Use low values for a better reaction time between the card and the reader. One time
slice is around 300us.
2.2.16 Selection Time-Out ISO 14443B (18h)
The default value is 10h. (~4.8mS)
The Selection Time-out represents the reader card communication time-out for the select, high-
speed select, continuous read, multi-list and multi-select commands with ISO 14443B tags. For a
better reaction time, use low values. One time slice is around 300µs.
speed select, continuous read, multi-list and multi-select commands with ISO 14443B tags. For a
better reaction time, use low values. One time slice is around 300µs.
2.2.17 Selection Time-Out SR176 (19h)
The default value is 10h. (~4.8mS)
The Selection Time-out represents the reader card communication time-out for the select,
continuous read, multi-list and multi-select command with SR176 tags. For a better reaction time,
use low values. One time slice is around 300µs.
continuous read, multi-list and multi-select command with SR176 tags. For a better reaction time,
use low values. One time slice is around 300µs.
2.2.18 Selection Time-Out ISO 15693 (1Ah)
The default value is 10h. (~9.6mS)
The Selection Time-out represents the reader card communication time-out for the select, high-
speed select, continuous read, multi-list, multi-select and MIFARE login command with ISO 15693
tags. Use low values for a better reaction time between the card and the reader. One time slice is
around 300us.
speed select, continuous read, multi-list, multi-select and MIFARE login command with ISO 15693
tags. Use low values for a better reaction time between the card and the reader. One time slice is
around 300us.
2.2.19 Protocol Configuration 3 (1Bh)
The Default value is 00h.
The protocol configuration register 3 (PCON3) further specifies the general behavior of the reader
device.
device.
Protocol configuration 3 register
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
SAK Extended
ID
ID
ReqA
Extended ID
Extended ID
ISO14443 Type B settings
RFU
Disable automatic
ISO 14443-4
timeouts
ISO 14443-4
timeouts
Page
Read
Read
2.2.19.1 Disable automatic ISO 14443-4 timeouts: bit 0 (default 0)
If Disable automatic ISO 14443-4 timeouts is set the automatic ISO 14443-4 timeouts are
disabled. The timeouts specified with TMR registers are used.
disabled. The timeouts specified with TMR registers are used.
2.2.19.2 Page read: bit 2 (default 0)
If set the continuous read mode retrieves the content of the tag instead of the serial number. The
register Page Start (1Ch) defines the start block and the Page Number (1Fh) defines the number
of blocks to be read.
register Page Start (1Ch) defines the start block and the Page Number (1Fh) defines the number
of blocks to be read.
August 2010
Page 33 of 144
© 2005-2010 HID Global Corporation. All rights reserved.