VTech Telecommunications Ltd 80-0289-00 Manual Do Utilizador

on purchasing your new VTech product. 
Before using this product, please read 
Important safety instructions. 

This manual has instructions on how to set 
up and pair your new baby unit. For complete 
instructions on using the baby unit, see the 
user’s manual that comes with your video and 
audio monitor.

For support, shopping, and everything new at 
VTech, visit our website at  
www.vtechphones.com.

Registration
Register your product online for 

enhanced warranty support.

Product news
Learn about the latest VTech  
products.

NOTES

Use only the power adapter supplied with this 

product.
Make sure the electrical outlet is not controlled 

by a wall switch.
The power adapter is intended to be correctly 

oriented in a vertical or floor mount position. The 

prongs are not designed to hold the plug in place 

if they are plugged into a ceiling, under-the-table 

or cabinet outlet.
Make sure the baby unit and the power adapter 

cord are out of reach of children.

•

•

•

•

d
e
f

g

a
b

c

h

i

j

k

n

l
m

1

2

3

4

5

Press to play or stop lullaby on the 

baby unit.

•

6

Press to adjust the baby unit 

speaker volume. It determines the 

lullaby volume and talkback volume 

transmitted from the parent unit.

•

7

Press to play the next lullaby.

•

8

On when the baby unit is turned on 

and is paired to the parent unit.
Flashes when the baby unit is not 

being viewed; or when the link to the 

parent unit is lost.

•

•

9

Slide to turn on or off the baby unit.

•

10

11

12

Press and hold to pair to the parent 

unit. 

•

13

For wall mount installation use.

•

14

Each newly purchased baby unit (

VM315) 

must be paired to your video and audio 
monitor system (

VM345 / VM345-2).

NOTES

You can pair a maximum of four baby units to 

your parent unit. Each new baby unit must be 

paired to the parent unit before use.
Make sure you power on the parent unit before 
pairing.

Press 

MENU when the parent unit is idle.

Press   or   to choose 

Pair/Unpair CAM, 

then press 

SELECT.

Press 

SELECT again to choose Pair CAM.

Press   or   to choose an empty baby unit 

slot, then press 

SELECT. 

The parent unit screen displays 

flashes.. Immediately press and hold 

PAIR on the bottom of the baby unit with 

a narrow pointed object such as a pencil. 

The LED light flashes quickly.

When pairing is successful, the screen 

displays the view of newly paired baby unit in  

SINGLE-CAM mode. The LED light on the 

new baby unit remains on.

NOTES

If pairing fails, the screen displays 

Pairing failed. 

Try the pairing process again.
Only one baby unit can be paired at a time.

•

•

1.
2.

3.
4.

5.

•

•

CAUTION

Keep the baby units out of the reach of your baby. 

Never place or mount the baby units inside the 

baby’s crib or playpen.

NOTE

To avoid interference from other electronic 

devices, place your baby monitor far away from 

devices such as wireless routers, microwaves, cell 

phones and computers.

Place the baby units more than 1 meter  

(3 feet) away from your baby.

>

 1m (3ft)

Adjust the angle of the baby unit camera to 

aim at your baby. 

Place the parent unit more than 1 meter  
(3 feet) away from the baby units.

63

63

>

 1m (3ft)

<

 1m (3ft)

CAUTION

The default volume of your parent unit is level 4. 

If you experience high-pitched screeching noise 

from your baby monitor while positioning:

Make sure your baby units and parent unit are 

more than 1 meter (3 feet) apart, OR
Turn down the volume of your parent unit.

•

•

1.

2.

3.

•

-

-

NOTE

Check for reception strength and camera angle 

before drilling the holes.

Place the wall mount bracket on a wall and 

then use a pencil to mark the top and the 

bottom holes as shown. Remove the wall 

mount bracket and drill two holes in the wall 

(7/32 inch drill bit).

If you drill the holes into a stud, go to step 3.
-OR-
If you drill the holes into an object other than 

a stud, insert the wall anchors into the holes. 

Tap gently on the ends with a hammer until 

the wall anchors are flush with the wall.

Align the wall mount bracket and screws 

with the holes in the wall as shown. Tighten 

the screw in the middle hole first, so that 

the wall mount bracket position is fixed. You 

can tighten the other screw in the top hole.
Place the baby unit on the wall mount 

bracket. Tighten the screw into the threaded 

socket at the bottom to secure the baby unit.

•

1.

2.

3.

-OR-
Insert the screws into the holes and tighten 

the screws until only 1/4 inch of the screws 

are exposed.
Place the baby unit on the wall mount 

bracket. Tighten the screw into the threaded 

socket at the bottom to secure the baby unit. 

Align the holes on the wall mount bracket 

with the screws on the wall, and slide the wall 

mount bracket down until it locks into place.

The default angle of the wall mount bracket 

is 90 degrees. You can maximize your 

baby unit’s viewing angles by tilting the 

wall mount bracket. 
Hold the baby unit, and then rotate the 

knob in anticlockwise direction. This will 

loosen the joint of the wall mount bracket. 

Tilt your baby unit up or down to adjust to 

your preferred angle. Then, rotate the knob 

in clockwise direction to tighten the joint 

and secure the angle.

The operating range of the baby monitor is 
up to 300 meters (1,000 feet) outdoors or 
50 meters (160 feet) indoors. The actual 
operating range may vary depending on 
the environmental conditions and other 
interferences such as walls, doors and other 
obstructions.

4.

NOTE

Make sure you power on the baby unit and the 
parent unit before unpairing the baby unit.

Press 

MENU when the parent unit is idle.

Press   or   to choose 

Pair/Unpair CAM, 

then press 

SELECT.

Press   or   to choose 

Unpair CAM, then 

press 

SELECT.

Press   or   to choose a desired baby 

unit, then press 

SELECT.

The screen displays 

Unit.. Press   on the parent unit.
The screen displays 

[MENU/SELECT] key to confirm.. Press 

SELECT to continue.
When unpairing is successful, the screen 

displays 

CAM X is unpaired and returns 

to previous menu. If there is no paired 

baby unit, the screen displays 

paired..The LED light on the selected baby 
unit flashes slowly. 

To keep this product working well and looking good, 

follow these guidelines:

Avoid putting it near heating appliances and 

devices that generate electrical noise (for 

example, motors or fluorescent lamps).
DO NOT expose it to direct sunlight or moisture.
Avoid dropping the product or treating it roughly.
Clean with a soft cloth.
DO NOT immerse the baby unit in water and do 

not clean them under the tap.
DO NOT use cleaning spray or liquid cleaners.
Make sure the baby unit is dry before you connect 

them to the mains again.

1.
2.

3.

4.

5.

6.

7.

•

•
•
•
•

•
•

When using your equipment, basic safety 

precautions should always be followed to reduce the 

risk of fire, electric shock and injury, including the 

following:

Follow all warnings and instructions marked on 

the product.
Adult setup is required.
This product is intended as an aid. It is not 

a substitute for responsible and proper adult 

supervision and should not be used as such.
This product is not intended for use as a 

medical monitor.
Do not use this product near water. For 

example, do not use it next to a bath tub, wash 

bowl, kitchen sink, laundry tub or swimming 

pool, or in a wet basement or shower.
Use only the adapters included with this 

product. Incorrect adapter polarity or voltage 

can seriously damage the product.  

Baby unit power adapter: Output: 5V DC 1A 
The power adapters are intended to be correctly 

oriented in a vertical or floor mount position. 

The prongs are not designed to hold the plug 

in place if it is plugged into a ceiling, under-the-

table or cabinet outlet.
For pluggable equipment, the socket-outlet 

shall be installed near the equipment and shall 

be easily accessible.
Unplug this product from the wall outlet before 

cleaning. Do not use liquid or aerosol cleaners. 

Use a damp cloth for cleaning.
Do not cut off the power adapters to replace them 

with other plugs, as this causes a hazardous 

situation.
Do not allow anything to rest on the power 

cords. Do not install this product where the 

cords may be walked on or crimped.
This product should be operated only from the 

type of power source indicated on the marking 

label. If you are not sure of the type of power 

supply in your home, consult your dealer or 

local power company.
Do not overload wall outlets or use an extension 

cord.
Do not place this product on an unstable table, 

shelf, stand or other unstable surfaces.
This product should not be placed in any area 

where proper ventilation is not provided. Slots 

and openings in the back or bottom of this 

product are provided for ventilation. To protect 

them from overheating, these openings must 

not be blocked by placing the product on a soft 

surface such as a bed, sofa or rug. This product 

should never be placed near or over a radiator 

or heat register.

1.

2.
3.

4.

5.

6.

7.

8.

9.

10.

11.

12.

13.

14.

15.