Everspring Industry Co Ltd SM122 Manual Do Utilizador
INSM122EVSP0E1A
SM122 Wireless Door/Window Alarm
As a small alarm system, Wireless Door/Window Alarm
can be easily placed onto an unsecured window or door
by connecting it with the external hardwire magnetic.
The Alarm emits a piercing 130 decibel alarm when the
alarm's magnetic seal is broken. It can be used either
as an alarm or an enunciator. It provides you with three
different modes to adapt to your home security needs.
As a small alarm system, Wireless Door/Window Alarm
can be easily placed onto an unsecured window or door
by connecting it with the external hardwire magnetic.
The Alarm emits a piercing 130 decibel alarm when the
alarm's magnetic seal is broken. It can be used either
as an alarm or an enunciator. It provides you with three
different modes to adapt to your home security needs.
(1) (2)
(3) (4)
(5)
INSTALLATION
1. Remove screw at the base of compartment and slide
1. Remove screw at the base of compartment and slide
off cover.
2. Mount the cover on the wall.
3. Insert the battery.
4. Slide on the cover to the wall and tighten the screw
3. Insert the battery.
4. Slide on the cover to the wall and tighten the screw
located at the base.
5. Mount magnetic sensor next to the siren on either the
left or right side of the alarm, with less than 10mm in
between. The Alarm will be triggered if the gap is
between. The Alarm will be triggered if the gap is
30mm or greater.
STARTING UP
Insert four (4) “AAA” size batteries. Average battery life
for typical usage is 1 year. When all batteries are
inserted, the Status LED will flash for one second to
indicate that the batteries are installed properly. The
Alarm will be started in the OFF mode. The four-digit
security code “1234” (PIN) has been set as the default
secret code. When you remove the battery, pressing
any button will clean out your previous setting. (NOTE:
After removing or replacing the batteries, the Alarm PIN
would be automatically set back as default “1234”.)
CODE LEARNING SETTING
Press the PIN code and key (e.g. [1]-[2]-[3]-[4]-[ ]) to
enter the code learning mode. The Alarm will transmit
a radio signal to the receiver instantly. Upon
completion of code learning transmission, the Alarm will
skip to off mode automatically. During code learning
mode, any input or activation will be ignored.
ARMING THE ALARM
Note: Both “Instant” and “Entry Delay” mode have a
15-second exit delay duration.
To set the Instant Mode, simply press the PIN code
and
key (e.g. [1]-[2]-[3]-[4]-[
]), this will result in
beeping sounds and the Status LED flashing, this
confirms the settings are completed. There will be a
15-second exit delay before the Alarm is armed. The
delay allows time for you to leave the protected area
without triggering the Alarm. The Alarm will transmit an
“open” radio signal to the receiver and sound for 30
seconds and then be silent for 10 seconds; with such a
40-second cycle for 10 times, when the magnetic
contact between the main unit and magnetic unit is
broken.
When the magnetic contact is closed again, the Alarm
will transmit a “close” radio signal to the receiver.
To set the Entry Delay Mode, simply press the PIN code
confirms the settings are completed. There will be a
15-second exit delay before the Alarm is armed. The
delay allows time for you to leave the protected area
without triggering the Alarm. The Alarm will transmit an
“open” radio signal to the receiver and sound for 30
seconds and then be silent for 10 seconds; with such a
40-second cycle for 10 times, when the magnetic
contact between the main unit and magnetic unit is
broken.
When the magnetic contact is closed again, the Alarm
will transmit a “close” radio signal to the receiver.
To set the Entry Delay Mode, simply press the PIN code
and
key (e.g. [1]-[2]-[3]-[4]-[
]), this will result in
beeping sounds and the Status LED flashing, this
confirms the setting has been completed. There will be
confirms the setting has been completed. There will be
a 15-second exit delay before the Alarm is armed. The
Status LED will flash for one second and a 15-second
silent entry delay before the alarm goes off when the
magnetic contact between the main unit and magnetic
unit is broken. The Alarm will emit an “open” radio signal
to the receiver and will sound for 30 seconds and then
be silent for 10 seconds; with such a 40-second cycle
for 10 times.
When the magnetic contact is closed again, the Alarm
will transmit a “close” radio signal to the receiver.
To set the Chime Mode, simply press the PIN code and
Status LED will flash for one second and a 15-second
silent entry delay before the alarm goes off when the
magnetic contact between the main unit and magnetic
unit is broken. The Alarm will emit an “open” radio signal
to the receiver and will sound for 30 seconds and then
be silent for 10 seconds; with such a 40-second cycle
for 10 times.
When the magnetic contact is closed again, the Alarm
will transmit a “close” radio signal to the receiver.
To set the Chime Mode, simply press the PIN code and
key ([1]-[2]-[3]-[4]-[
]); and this will cause one
chime, confirming that the setting has been completed.
Two chimes can be heard when the magnetic contact
between the main unit and magnetic unit is broken.
An “open” and “close” radio signal will be emitted
respectively when the magnetic seal is broken and
closed again.
DISARMING THE ALARM
Disarm the Alarm by pressing PIN and
Two chimes can be heard when the magnetic contact
between the main unit and magnetic unit is broken.
An “open” and “close” radio signal will be emitted
respectively when the magnetic seal is broken and
closed again.
DISARMING THE ALARM
Disarm the Alarm by pressing PIN and
key (e.g.
[1]-[2]-[3]-[4]-[
]).
When the Alarm is set in the off mode, any activation or
radio signal transmission will be ignored.
CHANGING PIN CODE
Press the PIN code and
key (e.g. [1]-[2]-[3]-[4]-[
]),
this will turn on both
LED and Status LED. If you do
not change the Pin Code or incorrect codes were
entered three times consecutively within 15 seconds,
the Alarm will automatically go into Off Mode.
While setting the PIN code, no radio signal will be
transmitted to the receiver if the magnetic seal is
broken.
BATTERY LOW INDICATION
When the battery is low, the
entered three times consecutively within 15 seconds,
the Alarm will automatically go into Off Mode.
While setting the PIN code, no radio signal will be
transmitted to the receiver if the magnetic seal is
broken.
BATTERY LOW INDICATION
When the battery is low, the
LED will flash every 3
seconds until the battery dies. Low battery indication
won’t be visible until the Alarm is at idle condition which
means alarm activation, code input, 30-seconds
disabled period, delay mode and code clearance will not
be indicated.
won’t be visible until the Alarm is at idle condition which
means alarm activation, code input, 30-seconds
disabled period, delay mode and code clearance will not
be indicated.