Rosslare Enterprises Ltd XR-16AG Manual Do Utilizador
MatrixBus™ XR-16A
Installation Instructions
AuraSys™ L-4/6 Wireless Zone Expansion
1
0706-0960344+01
1. Introduction
This wireless expansion transforms the AuraSysä Lite system from a
limited hardwired system into a wireless system. The expansion is a
two way RF communicator which allows connection to wireless
sensors, sirens, keypads, repeaters and remote controls.
With up to 4/6 zones depending on the hosting panel having the
With up to 4/6 zones depending on the hosting panel having the
same characteristics as the on board zones.
The stand alone expansion option is housed in a plastic casing
The stand alone expansion option is housed in a plastic casing
installed outside of the system's case considering RF environment
and wireless devices deployment.
2. Technical Specifications
2.1. Electrical Characteristics
Auxiliary Voltage: 13.4 – 13.8 VDC from hosting panel
Maximum Input Current: 55-75 mA
Indication:
Maximum Input Current: 55-75 mA
Indication:
2.2. Environmental Characteristics
Red LED
Operating Environment: indoor use
Operating Temperature: -10°C to 50°C (14°F to 122°F)
Operating Humidity: 0 to 95% (Non-Condensing)
Operating Temperature: -10°C to 50°C (14°F to 122°F)
Operating Humidity: 0 to 95% (Non-Condensing)
RFI Protection:
2.3. Physical Characteristics (with case)
>20 V/m up to 1000 MHz.
Dimensions (HxWxD): 101 x 99 x 35 mm (4 x 3.9 x1.4 in)
Weight:
Weight:
2.4. Available models:
143 g (0.316 lbs)
XR-16AH – 868.35 MHz
XR-16AG – 433.92 MHz
XR-16AG – 433.92 MHz
3. Installation
3.1. General
The XR-16A is designed for easy installation. Only a few steps are
required to install the keypad.
Changes or modifications to this equipment not expressly
Changes or modifications to this equipment not expressly
approved by Rosslare security as the party responsible for
compliance could void the user’s authority to operate the
equipment.
3.2. Mounting the XR-16A expansion
Perform the following steps to mount the expansion:
1) Remove the four screws holding the front cover. Set the
1) Remove the four screws holding the front cover. Set the
screws aside.
2) Disassemble the PCB assembly from the back plate, remove
the four screws holding the PCB, set them aside.
3) Locate the back plate at the desired installation location.
The wireless expansion should be installed at a secured
location considering RF environment and wireless devices
deployment.
4) Use the back cover itself as a template for the wall screws.
5) Drill holes in the wall and insert anchors. Hardware is
5) Drill holes in the wall and insert anchors. Hardware is
provided.
6) Route a four-wire cable from the panel to the wireless
expansion location.
7) Pass the 4-wire cable via one of the channels designed in
the back plate. Use pliers to remove the section covering
the channel.
8) Mount and fasten the back plate using the screws provided.
Make sure to level the plate.
9) Make wiring connections, to the PCB assembly and mount
on the back plate.
10) Secure with the screws, set aside previously.
3.3. Wiring
Refer to the wiring diagram below.
NOTE: Wiring must be done when the AuraSys™ L-4/6 panel
power is turned off.
4. Configuration
4.1. LEDs
The module LED flashes red until the panel finishes initialization of
Wireless module. After initialization, the wireless module turns the
LED on continuously.
During normal operation, when the module is in programming
During normal operation, when the module is in programming
mode, or any time the module is LOCKED, the LED flashes red.
4.2. Tamper
The stand alone expansion option cover and back tamper
switches prevent vandalism and unauthorized PCB access.
The module continuously checks the Tampers status when JP5 is
disconnected.
The JP5 jumper is the Tamper jumper. When using the expansion
The JP5 jumper is the Tamper jumper. When using the expansion
on the board inside the metal casing the tampers must be
shorted in order to prevent false alarms.
When operating as a stand alone module, jumper JP5 must be
When operating as a stand alone module, jumper JP5 must be
open (no jumper).
MatrixBUS
XR-16A
XR-16A