INNCOM International Inc. 027060TXR Manual Do Utilizador
M O D E V A R e f e r e n c e M a n u a l
P a g e 5 o f 1 6
all logic communications and interfacing capability, it can be used as a low-voltage remote control interface for load
center style applications.
center style applications.
4.1 RF capability
MODEVA shares the electrical design of the 0dB 2.4GHz 802.15.4 INNCOM TXR radio module by embedding the
radio components in the logic board. This sub-circuit has been specifically tuned for optimal performance for the
guestroom environment. Typically, the RF transceiver can expect to reach up to a 70ft radius in an indoor, urban
environment. MODEVA communicates on the standard INNCOM RF protocol, a proprietary encrypted protocol
that runs over the 802.15.4 platform stack. This is a shared protocol that is used by all other RF capable INNCOM
products. The protocol’s encryption method provides protection for the P5 frame being sent into the RF spectrum
and makes it very difficult to interpret the data and reuse it maliciously.
radio components in the logic board. This sub-circuit has been specifically tuned for optimal performance for the
guestroom environment. Typically, the RF transceiver can expect to reach up to a 70ft radius in an indoor, urban
environment. MODEVA communicates on the standard INNCOM RF protocol, a proprietary encrypted protocol
that runs over the 802.15.4 platform stack. This is a shared protocol that is used by all other RF capable INNCOM
products. The protocol’s encryption method provides protection for the P5 frame being sent into the RF spectrum
and makes it very difficult to interpret the data and reuse it maliciously.
Note: RF performance can be degraded by pre existing environmental factors.
4.2 S5-bus
The logic board incorporates the most modern S5-bus circuit design, to support up to 15 S5-bus devices in a single
guestroom network segment.
guestroom network segment.
4.3 IR Tx and Rx
MODEVA uses a low power IR transmitter and receiver to provide two functions: IR communications for TV and
A/V system control and proximity detection. This circuit is not to be confused with IR5 and cannot be used as a
wireless IR5 transceiver for IRAS and guestroom network purposes.
A/V system control and proximity detection. This circuit is not to be confused with IR5 and cannot be used as a
wireless IR5 transceiver for IRAS and guestroom network purposes.
5 Load Assembly
The Load Assembly is the core of MODEVA system flexibility. The Load Assembly consists of mounting brackets
and WBI actuators that provide the mechanical platform and load bearing capability for the MODEVA system.
Each MODEVA (and each input located on the interface) can control any one of the individual actuators as part of
the Load Assembly located within the local gang box, or it can remotely control other actuators as part of the
guestroom network IRAS. This allows the designer to locate actuators with specifically designed functions
throughout the guestroom network and to have control over that actuator from any user interface in the
guestroom network. The MODEVA platform uses magnets located on the back side of the logic board that adhere
to the large flat metal surfaces of the Load Assembly brackets, allowing for screwless mounting that adds to the
aesthetic product design.
and WBI actuators that provide the mechanical platform and load bearing capability for the MODEVA system.
Each MODEVA (and each input located on the interface) can control any one of the individual actuators as part of
the Load Assembly located within the local gang box, or it can remotely control other actuators as part of the
guestroom network IRAS. This allows the designer to locate actuators with specifically designed functions
throughout the guestroom network and to have control over that actuator from any user interface in the
guestroom network. The MODEVA platform uses magnets located on the back side of the logic board that adhere
to the large flat metal surfaces of the Load Assembly brackets, allowing for screwless mounting that adds to the
aesthetic product design.
5.1 Categories of Load Assembly Load Switching
5.1.1 TRIAC Dimmer Power Supply
The TRIAC dimmer provides dimming control of
resistive light loads such as incandescent, halogen, and
TRIAC dimmable LEDs. The TRIAC dimmer can dim
100–120VAC loads up to 500W.
resistive light loads such as incandescent, halogen, and
TRIAC dimmable LEDs. The TRIAC dimmer can dim
100–120VAC loads up to 500W.
The TRIAC Actuator also provides a class-2, 12VDC
output used to power the MODEVA logic and touch
user interface and to provide connection and power for a
wired S5-bus IRAS network.
output used to power the MODEVA logic and touch
user interface and to provide connection and power for a
wired S5-bus IRAS network.
Figure 4 Load Assembly Frame