Climax Technology Co Ltd DC18 Manual Do Utilizador
2
B
B
a
a
t
t
t
t
e
e
r
r
y
y
The Door Contact uses one CR123A, 3V Lithium battery as its power source. Please note: ALWAYS replace battery
with the correct size and voltage.
The Door Contact can detect if the battery is low. When the Battery is low, a low battery signal will be sent to the
Control Panel along with regular transmission. The LED will also flash quickly for 2 seconds when the Door Contact is
activated under low battery status.
activated under low battery status.
When the battery is depleted, the LED flashes once every 4 seconds and the Door Contact will stop all function.
Battery Change
I.
Detach the base and cover assembly.
II. Remove the old battery.
III. Press the Tamper Switch a few times.
IV. Fit a new battery into the battery compartment. Please orient the battery according to the correct polarity.
V. Reattach the base and cover assembly.
III. Press the Tamper Switch a few times.
IV. Fit a new battery into the battery compartment. Please orient the battery according to the correct polarity.
V. Reattach the base and cover assembly.
T
T
a
a
m
m
p
p
e
e
r
r
S
S
w
w
i
i
t
t
c
c
h
h
Tamper Switch provides tamper protection against unauthorized device opening.
The Tamper switch is in normal operating position (Tamper closed) when the spring is compressed against the inside
of device cover. Tamper violation happens when the cover is removed from the base and releases the tamper switch.
S
S
u
u
p
p
e
e
r
r
v
v
i
i
s
s
o
o
r
r
y
y
S
S
i
i
g
g
n
n
a
a
l
l
The Door Contact will automatically transmit Supervisory Signals periodically to the Control Panel at random intervals
of 30-50 minutes.
The supervision time is reset whenever a signal is transmitted. (such as Tamper open signal, Tamper close signal,
etc.).
G
G
e
e
t
t
t
t
i
i
n
n
g
g
S
S
t
t
a
a
r
r
t
t
e
e
d
d
Detach the base and cover assembly.
Insert the “CR123A” battery into the battery holder connecting the polarity correctly.
Put the Control Panel into learning mode. Please refer to your Control Panel user
manual.
Press and release the Tamper Switch twice to send learn code to Control Panel.
Refer to your Control Panel operation manual’s to complete the learn-in process.
To check for range, please refer to the control panel user manual for what type of
signal transmission is needed from the Door Contact. (A Tamper open signal is
usually needed)
usually needed)
Proceed with mounting and installation once you are satisfied with the location of the
Door Contact.
M
M
o
o
u
u
n
n
t
t
i
i
n
n
g
g
M
M
e
e
t
t
h
h
o
o
d
d
s
s
a
a
n
n
d
d
I
I
n
n
s
s
t
t
a
a
l
l
l
l
a
a
t
t
i
i
o
o
n
n
It is recommended that the Door Contact should be placed on the door frame and
the magnet on the door.
the magnet on the door.
Step 1: Find a suitable location close to a door/window to install the Door Contact.
Step 2: Option A: Base mounting:
I.
Detach the base and cover assembly
II. Using the mounting holes as templates, drill holes in the
surface
III. Insert the wall plugs if fixing into plaster or brick
IV. Screw the base into the wall plugs
V. Reattach the base and cover assembly
Option B: Using the Mounting Bracket:
I.
IV. Screw the base into the wall plugs
V. Reattach the base and cover assembly
Option B: Using the Mounting Bracket:
I.
Using the Bracket Mounting Holes as templates, drill holes in
the surface
II. Insert the wall plugs if fixing into plaster or brick
III. Screw the Mounting Bracket into the wall plugs
IV. Hook the Door Contact onto the Mounting Bracket
III. Screw the Mounting Bracket into the wall plugs
IV. Hook the Door Contact onto the Mounting Bracket