Manualsbrain.com
  1. Manuais
  2. Marcas
  3. Climax Technology Co Ltd
  4. IRZB
  5. Manual Do Utilizador

Climax Technology Co Ltd IRZB Manual Do Utilizador

Download
Página de 5
 
3
2.  The PIR has been reset to factory default setting with all its previous network information removed. It 
will now actively search for available ZigBee network again and join the network automatically.   
3.  If the PIR successfully joins a ZigBee network, the LED Indicator will flash twice to indicate. 
 
Installation 
 
 
I
I
n
n
s
s
t
t
a
a
l
l
l
l
a
a
t
t
i
i
o
o
n
n
 
 
G
G
u
u
i
i
d
d
e
e
l
l
i
i
n
n
e
e
 
 
 
The PIR is designed to be mounted on either a flat surface or in a corner situation with fixing screws 
and plugs provided.   
 
It is recommended to install the PIR in the following locations. 
 
In a position such that an intruder would normally move across the PIR’s field of view. 
 
Between 1.9 and 2m above ground for best performance. 
 
In a corner to give the widest view. 
 
Where its field of view will not be obstructed e.g. by curtains, ornaments etc. 
 
Pet Immunity (IRP-9ZBSSL Only): 
 
Refer to diagram to the right for PIR pet immunity coverage. 
 
If required, you can adjust the height of the PIR according 
to the size of your pet for optimal pet immune performance. 
Higher installation location will provide large pet-immune 
space, but also increases the blind spot under the PIR. 
 
Limitations 
 
Do not install the PIR at location exposed direct sunlight, or 
close to heating/cooling appliance and vent 
 
Do not point the PIR at heat source such as heater, radiator 
and window. 
 
Do not point the PIR at window. 
 
Avoid large obstacles in the detection area, and avoid moving objects such as curtain. 
 
Avoid locations where pet may climb on and compromise pet immunity, such as stairway. 
 
 
U
U
s
s
i
i
n
n
g
g
 
 
P
P
I
I
R
R
 
 
w
w
i
i
t
t
h
h
 
 
Z
Z
i
i
g
g
B
B
e
e
e
e
 
 
R
R
o
o
u
u
t
t
e
e
r
r
 
 
IMPORTANT NOTE 
If PIR installation location is away from your system control panel and requires ZigBee routers to improve 
signal strength. DO NOT use a ZigBee Router without backup battery. A ZigBee router without battery will 
be powered down during AC power failure and the PIR connected to the router will lose connection with 
ZigBee network. You should plan your PIR installation location using only ZigBee router with backup 
battery. 
 
 
M
M
o
o
u
u
n
n
t
t
i
i
n
n
g
g
 
 
t
t
h
h
e
e
 
 
P
P
I
I
R
R
 
 
 
Surface mounting: 
1.  Remove the fixing screw and cover assembly. 
2.  Break through the 4 wall mounting knockouts on the base. 
3.  Using the holes as a template, drill holes in the surface. 
4.  Insert the wall plugs if fixing it into plaster or brick. 
5.  Screw the base into the wall plugs. 
6.  Replace the front cover on the back cover. 
 
Corner mounting: 
1.  Remove the fixing screw and cover assembly. 
2.  Break through the 4 corner fixing knockouts on the edge of back cover. 
3.  Using the corner fixing knockouts as a template, drill holes into in the corner. 
4.  Insert the wall plugs if fixing it into plaster or brick. 
5.  Screw the back cover onto the wall plugs 
6.  Replace the front cover on the back cover.