MOTREX CO. LTD. AT-E1000P Manual Do Utilizador

1

2

3

4

Power DC : Insert Power Supply
LAN Port : Connect Ethernet cable
HDMI OUT :  Connect to display device 
Touch USB IN Port :  Connect to a touch display

5

6

7

Status LED 
Home button :  Return to Home screen
Power Switch :  Turn Receiver ON/OFF

1

2

3

4

Connect HDMI cable from touch display to the HDMI OUT port of the KinectIQ PRO Receiver.
Connect USB cable from touch display to the Touch IN USB port of the Receiver.
Connect the Power Supply provided to the Power In port of the Receiver. 
Turn Power Switch On. 

1

2

3

Power adapter

USB
HDMI

1

2

3

4

5

Remove Touch USB Dongle from KinectIQ PRO Transmitter.
Insert Touch USB Dongle into the USB IN port of your laptop or PC. 
Plug KinectIQ PRO Transmitter in to the HDMI out port of laptop or PC. Use the HDMI extension cable provided if needed. 
Slide the power switch to the left to turn power ON and the Status LED will light blue.
Click Transmit button and an image will appear on the display device of which the Receiver is installed.

• If multiple Transmitters are connected, the corresponding screen of the Transmitter that has just been clicked will appear, as part of 

the product’s integrated switching function. 

Pair the transmitter with the Receiver by entering Set Mode in the Settings.

PAIR

Ready for PAIRING

Connect the Touch USB dongle to the USB port of 
laptop or PC.
Press and hold the Transmit Button while switching the 
power switch to ON. Keep holding the Transmit Button
for ~10 seconds until status LED starts flashing blue.

1

1

5

4

3

2

2

2

When paired, the IP address will appear on the Set Mode 
Check window.
For additional Transmitters, repeat above procedure.
- Remove the USB Dongle from laptop upon setup.
- Upon each new Transmitter paired, please check that a new 

IP address is added on the Set Mode Check window.

Click on the X button at the top right corner of the Set Mode 
Check window to exit the setup procedure.

3

4

5

Click on the Add New Device Button to enter Set Mode
Click on Add New Device at the bottom of the Set Mode Check window to pair additional KinectIQ PRO Transmitters.
Set Transmitter Color.
To remove a Transmitter that has already been paired, click on the X button to the right of the paired Transmitter. 
When all Transmitters have been paired, click on the X button at the top right corner of the Set Mode Check window to exit the setup procedure

1

1

2

2

3

4

5

3

4

5

Click NEXT on the lower right corner of the yellow pop-up window.
Check the Mac address of newly registered Touch USB dongle.
Click on the X button at top right corner of the Set Mode Check window to exit the setup procedure.

The distance available for wireless application may vary depending on the user environment.  
The wireless device in use may be subjected to radio interference during operation. 
The screen in part may not show if the aspect ratio of image being replayed does not match with that of the monitor. 
Turn power OFF of the product and of the Transmitter when not in use.

The distance available for wireless application may vary depending on the user environment.  
The wireless device in use may be subjected to radio interference during operation. 
The screen in part may not show if the aspect ratio of image being replayed does not match with that of the monitor. 
Turn power OFF of the product and of the Transmitter when not in use.

4
5
6

4

6

5

Click on the Add New Device Button to enter Set Mode.
Click on the Mac address of the Touch USB dongle to re-register 
within the Set Mode Check window.
Connect the Touch USB dongle in a laptop to start pairing. 
(Only one USB dongle shall be connected to laptop 
  for new registration)

1

2

2

3

3

1

     While mirroring, click on the overlay annotation icon to 
      take notes and draw on your display screen. This feature 
      allows for full interactivity of your presentation.

- Overlay annotation is feasible on word files, image files, 

         internet browser files, etc 

        Overlay annotation thumbnail

 - Save overlay annotations as pdf file
 - Click on overlay annotation thumbnail to view on 

screen

2

1

3

4

6

5

2

1

2

3

4

5

6

3

1

1

2

      Overlay Annotation Tool

- Tool Layout 

3

Basic tools : pen, highlighter, eraser
Set line thickness
Add new page : save current page and add a new page
White board 
Share : save/share files via email, QR Code, Cloud 
Exit

- Pen Setting :      Click       Select pen color, width

1

2

1) QR Code : Smart device QR Code reader

Smart device, KinectIQ Receiver must be connected to same 

 Wi-fi network

5

- Share :     Share via E-mail, QR-code Scan, Cloud

Choose color

Current color

Width

Erase entire screen

Select width

1

- Eraser :         Click