Digital Monitoring Products Inc PC0136 Manual Do Utilizador

3

Terminals 5-11 on J9 connect grounded zones 1 through 3.  These zones 

have a grounded side and cannot be used for fire-initiating devices.  Zones 

2 and 3 can also be used for access control with Zone 2 providing a bypass 

option and Zone 3 providing Request to Exit functionality.  Zone 4 terminals 

provide a non-powered Class B, Style A zone. Use the supplied, DMP 

Model 311 1K Ohm End-of-Line resistors on each zone.  Refer to the panel 

programming guide for programming instructions.

Any burglary device

No

Door Contact

No

REX (PIR or Button)

No

Any device

Yes

The 4-pin J26 header located on the far right of the circuit board is used to wire the Armed Status, Remote Annunciation, 

and the Remote LED Control. The open collectors will supply a ground for a 

maximum current of 50mA @ 30 VDC. Connect a Model 300 4-wire harness to 

the 4-pin header for connection of the following indicators:
--AS (Armed Status)
Armed Status provides an unsupervised switched ground for a visual or audible 

armed status indicator that turns on when the burglary areas are armed, such 

as SYSTEM ON or ALL SYSTEM ON.  Connect the wire from the 4-wire harness to 

an Armed Status output. 
--RA (Remote Annunciation)
Remote Annunciation provides an unsupervised switched ground for a remote 

annunciator that turns on when the Model 734W on-board piezo turns on.  

Connect the wire from the 4-wire harness to a remote annunciator.  The 

remote annunciator silences when the RA restores.  The remote annunciator (RA) switched ground will operate even if the 

speaker is programmed not to operate. 
--LC (Remote LED Control)
Remote LED Control provides an unsupervised switched ground for a visual indicator that turns on when the Model 734W 

relay activates.  Connect the wire from the 4-wire harness to an LED.  The LED turns on for the duration the door strike 

relay is on. HID readers optionally provide a connection for LED reader control.

The 734W controls Auxiliary Outputs 1 and 2 when the Activate Zone 2 Bypass programming option is enabled and the Zone 

2 Bypass Time is set. When the door contact (Zone 2) is opened while the door strike is 

activated, the Zone 2 Bypass Time starts. If the door has not closed at the end of the timer, 

Aux Output 1 is turned on and the timer starts again. If the door is still open at the end of the 

second timer, Aux Output 2 is turned on. Aux Outputs 1 and 2 turn off when the door contact  

is closed. Use the Model 431 Relay Harness for connection of Output 1 and Output 2 as shown 

in Table 1.

The reset header is located just above and to the right of the WiFi network connector (see Figure 1) and is used to reset 

the 734W module. To reset the module when first installing the system, install the reset jumper before applying power to 

the module. After connecting the power, remove the reset jumper. 
To reset the module while the system is operational, for example, prior to reprogramming, install the reset jumper 

without powering down the system. Remove the reset jumper after one or two seconds.

The 734W module is programmable from a 32-character keypad set to address one. For 

12 Volt applications, connect the 

keypad to the module using a Model 330 4-wire harness.  
For 

24 Volt applications, connect the keypad to the module using the included WR-0235 4-wire programming harness with 

in-line resistor. 

While programming the 734W module with a keypad, advance to the next programming option by pressing the CMD key.  

Return to the previous programming option or erase an incorrect entry by pressing the Back Arrow key.  Make a selection 

by pressing the Select key below the option you wish to select.  While in programming mode no 734W communication with 

the panel can occur.

Remote Audible Annunciator

Armed Status Output

Output 2

Output 1

Remote LED Control

Output Color Code–Model 431 Harness

Output 2   N/O   Orange/White

Output 2  Com  White/Gray

Output 2  N/C  Violet/White

Output 1  N/O  Orange

Output 1  Com  Gray

Output 1  N/C  Violet