Manualsbrain.com
  1. Manuais
  2. Marcas
  3. Sam Ash Music Corporation
  4. CB88
  5. Manual Do Utilizador

Sam Ash Music Corporation CB88 Manual Do Utilizador

Download
Página de 10
15
Concert 88 Wireless System
Quick Start - Single System Setup
This device complies with Part 15 of the 
FCC Rules. Operation is subject to the 
following two conditions:
(1) This device may not cause harmful 
       interference, and
(2) this device must accept any 
       interference received, including
       interference that may cause
       undesired operation.  
FREQ:
542-566MHz
This device complies with Part 15 of the 
FCC Rules. Operation is subject to the 
following two conditions:
(1) This device may not cause harmful 
       interference, and
(2) this device must accept any 
       interference received, including
       interference that may cause
       undesired operation.  
FREQ:
542-566MHz
3. Plug in receiver
4. Turn on receiver
5. Plug receiver into audio system
6. Press Select button to change channel
9. Press and hold SELECT button to IR set
10. Adjust Volume control
7. Install batteries
8. Press button on transmitter to turn on
9. Press and hold Select button to IR set
7. Install batteries
8. Turn on belt pack transmitter
This device complies with Part 15 of the 
FCC Rules. Operation is subject to the 
following two conditions:
(1) This device may not cause harmful 
       interference, and
(2) this device must accept any 
       interference received, including
       interference that may cause
       undesired operation.  
FREQ:
542-566MHz
This device complies with Part 15 of the 
FCC Rules. Operation is subject to the 
following two conditions:
(1) This device may not cause harmful 
       interference, and
(2) this device must accept any 
       interference received, including
       interference that may cause
       undesired operation.  
FREQ:
542-566MHz
3. Plug in receiver
4. Turn on receiver
5. Plug receiver into audio system
6. Press Select button to change channel
9. Press and hold SELECT button to IR set
10. Adjust Volume control
7. Install batteries
8. Press button on transmitter to turn on
9. Press and hold Select button to IR set
7. Install batteries
8. Turn on belt pack transmitter
Position the transmitter about 6-12" (15-30 cm) from the front of the CR88 with 
the transmitter's IR window facing the IR transmitter on the front panel of the CR88 
receiver.
This device complies with Part 15 of the 
FCC Rules. Operation is subject to the 
following two conditions:
(1) This device may not cause harmful 
       interference, and
(2) this device must accept any 
       interference received, including
       interference that may cause
       undesired operation.  
FREQ:
542-566MHz
This device complies with Part 15 of the 
FCC Rules. Operation is subject to the 
following two conditions:
(1) This device may not cause harmful 
       interference, and
(2) this device must accept any 
       interference received, including
       interference that may cause
       undesired operation.  
FREQ:
542-566MHz
3. Plug in receiver
4. Turn on receiver
5. Plug receiver into audio system
6. Press Select button to change channel
9. Press and hold SELECT button to IR set
10. Adjust Volume control
7. Install batteries
8. Press button on transmitter to turn on
9. Press and hold Select button to IR set
7. Install batteries
8. Turn on belt pack transmitter
This device complies with Part 15 of the 
FCC Rules. Operation is subject to the 
following two conditions:
(1) This device may not cause harmful 
       interference, and
(2) this device must accept any 
       interference received, including
       interference that may cause
       undesired operation.  
FREQ:
542-566MHz
This device complies with Part 15 of the 
FCC Rules. Operation is subject to the 
following two conditions:
(1) This device may not cause harmful 
       interference, and
(2) this device must accept any 
       interference received, including
       interference that may cause
       undesired operation.  
FREQ:
542-566MHz
3. Plug in receiver
4. Turn on receiver
5. Plug receiver into audio system
6. Press Select button to change channel
9. Press and hold SELECT button to IR set
10. Adjust Volume control
7. Install batteries
8. Press button on transmitter to turn on
9. Press and hold Select button to IR set
7. Install batteries
8. Turn on belt pack transmitter
Press and hold the CR88 SELECT button to set the 
transmitter to the same channel as the receiver via 
infrared transmission
Press the SELECT button on the front of the CR88 
receiver to choose an available channel. The channel 
number will increase by one digit, from 0-9 then A-F. 
Once the last channel has been reached, the count will 
cycle back to 0.