Fashion Star Technology Limited F-456AB Manual Do Utilizador

 
 
 
 

 

 
 

 

1.  This product is only equipped for radio controlled 

models; 

2.  The usage of this product should be approved by local 

relevant law or regulations;   

3.  We will not be responsible for the damages caused by 

unauthorized modification, adjustment or replacement 

of parts of this product;   

4.  The manual may be altered without prior notice. 

Please contact us if you have any corrections or 

clarifications that should be made in the manual.   

 ¾ Before starting the transmitter, make sure the transmitter 

batteries are well loaded .The voltage of transmitter 

batteries is never lower than 4.6V. And please check and 

confirm that the servos are all well and properly 

connected.  

¾ Keep the radio system away from moist, high temperature 

and strong shake. Do not clean the product with solvent.   

¾ The antenna does not touch anything else when power 

switch is turned on. Do not leave this product and its 

accessories within the reach of small children.   

¾ Please use this product according to your local relevant 

law or regulation, we are not responsible for any incidents 

or damages. 

1. Power on the receiver, the LED of transmitter flash 

slowly to show it is scanning the transmitter. After about 

6 seconds, the receiver goes to binding mode, the LED 

flash quickly. 

2.  Press and hold the BIND button, then power on the 

transmitter. The LED of transmitter flash with RED and 

GREEN, the transmitter goes into binding mode. 

3.  Transmitter and receiver begin to bind. After binding is 

completed, the LED of transmitter and receiver will 

change to solid GREEN. Otherwise, please repeat the 

above operation again. 

Power on the transmitter, the LED of transmitter turns 

GREEN. 

Power on the receiver, when the LED of receiver turns 

GREEN, the device is paired and prepared to work. 
Turn off 

Remove the power of receiver. 

Power off the transmitter. 

Switch 

Switch 1

Switch 2

Switch 3

Switch 4 

Switch 5

Switch 6 

Reverse

Aileron 

Reverse

Elevator 

Reverse

Throttle 
Reverse

Rudder 

Reverse

Mode1 
Mode2 

Fixed-Wing 

Delta 

¾ Receiver channel distribution:   

Ch1: Aileron   Ch2: Elevator  Ch3: Throttle    Ch4: Rudder 

¾ Switch to “DELTA” position and enter DELTA mode, aileron 

and elevator is mixed, as for triangle planes, tailless planes. 

Transmitter 

Receiver Channel Mixing 

Stick CH1 CH2 

Aileron Stick 

+50% 

+50% 

Elevator Stick 

+50% 

-50% 

¾ Receiver channel distribution:   

Ch1: Aileron   Ch2: Elevator  Ch3: Throttle    Ch4: Rudder 

¾ Switch to “FIXED-WING” position and enter FIXED-WING 

Plane mode. 

Receiver Channel Distribution: 
CH1:Aileron 
CH2:Elevator 

CH3:Throttle 
CH4:Rudder 

Receiver Channel Distribution: 
CH1:Aileron 
CH2:Elevator 

CH3:Throttle 
CH4:Rudder 

Transmitter 

Item: F-4   

Channels: 4   

Resolution: 1024   

Frequency: 2.4GHz ISM Frequency Range   

Spread Spectrum Mode: FHSS   

Frequency point: 152PCS 

Bandwidth: 500kHz   

Frequency interval: 4M 

Output Power: ≤100mW  

Working current: ≤150mA  

Working voltage: 1.2V*4NiCad/NiMH   

Dimensions: 152mm * 163mm * 65mm   

Net weight: 252g   

 

Receiver     

Channels: 4   

Frequency: 2.4GHz ISM Frequency range   

Spread Spectrum Mode: FHSS   

Power: 4.8-6.0V 

Measurement: 30.1mm * 17.4mm * 11.7mm 

Net weight: 3.6g   

When the LED starts blinking quickly with RED and 

GREEN, please change the battery immediately. 

Do NOT operate your radio below low battery. Always shut 

your device off as soon as possible after the low battery 

warning loss of control.