Intermatic CA5000 Manual Do Utilizador
WARNING: Read instructions completely before installation and retain for future reference.
WARNING:
WARNING:
WARNING:
WARNING:
OTHER CAUTIONS:
For installation and/or use in accordance with appropriate electrical codes and regulations.
Consult a qualified electrician for installation and operation.
Consult a qualified electrician for installation and operation.
1. For remote operation of Z-Wave compatible controls.
2. Use this device only with copper or copper clad wire.
2. Use this device only with copper or copper clad wire.
Note: Designed to work only in the presence of InTouch™ Server (CA5500B or other).
Model CA5000
Multi-Scene Wall Controller
Specifications:
Ratings:
Colors:
Connections:
RF Information:
Network Information:
Wireless RF Control
120VAC, 50/60Hz
Includes white, ivory, and light almond
snap-on face plates.
snap-on face plates.
Black-Line, White-Neutral,
Green-Ground
Green-Ground
Minimum Range:
50ft indoor; 100ft outdoor
Frequency: 908.42 MHz
50ft indoor; 100ft outdoor
Frequency: 908.42 MHz
Mesh Network - Each line powered
node acts as a repeater to route
distant signals.
Data Rate: 9600 bits/second
Size: 232 Z-Wave™ Nodes
node acts as a repeater to route
distant signals.
Data Rate: 9600 bits/second
Size: 232 Z-Wave™ Nodes
Operating Temperature Range:
32°F (0°C) to 104°F (40°C)
Power Consumption: 2.0W Max
32°F (0°C) to 104°F (40°C)
Power Consumption: 2.0W Max
INSTALLATION:
1. WARNING: TO AVOID FIRE, SHOCK, OR DEATH, TURN OFF POWER AT CIRCUIT BREAKER AND
TEST THAT POWER IS OFF BEFORE WIRING.
1. WARNING: TO AVOID FIRE, SHOCK, OR DEATH, TURN OFF POWER AT CIRCUIT BREAKER AND
TEST THAT POWER IS OFF BEFORE WIRING.
Operation:
2. Refer to wiring diagrams for proper connection of multi-scene wall controller.
3. Check that all wire connections are secure.
4. Place all wires inside junction box. Install multi-scene wall controller using (2) mounting screws furnished.
Complete installation with a decorator style wall-plate.
5. Reconnect your electrical power.
6.
3. Check that all wire connections are secure.
4. Place all wires inside junction box. Install multi-scene wall controller using (2) mounting screws furnished.
Complete installation with a decorator style wall-plate.
5. Reconnect your electrical power.
6.
Press scene number button(s) to focus control activities; Press “Enter” to toggle selected
scene(s); Press
7. For programming instructions refer to the
(158CA12789).
InTouch Installer & Users Guide
r s
/
to raise or lower selected scene(s) level; Press the home key to clear selected
scene(s).
The CA5000 Multi-Scene Wall Controller is an enhanced radio frequency controller compatible with Z-wave™
enabled networks and devices. Each line powered node in a Z-wave network is designed to act as a repeater
forming a mesh network eliminating radio “dead spots” and providing the highest level of reliability.
enabled networks and devices. Each line powered node in a Z-wave network is designed to act as a repeater
forming a mesh network eliminating radio “dead spots” and providing the highest level of reliability.
- Multiple location On/Off & Raise/Lower control when used with Z-wave enabled devices.
- Allows control of up to 6 individual pre-set scenes containing any number of Z-wave enabled devices.
- Features individual scene status feedback for enhanced control.
- Separate focus and control buttons allow the user to custom mix scene selections and vary light levels.
- Home key provides for quick de-selection of scenes.
- Allows control of up to 6 individual pre-set scenes containing any number of Z-wave enabled devices.
- Features individual scene status feedback for enhanced control.
- Separate focus and control buttons allow the user to custom mix scene selections and vary light levels.
- Home key provides for quick de-selection of scenes.
Features
Faceplate
Snap
Snap
FCC STATEMENT OF COMPLIANCE
WARNING! Changes or modifications not expressly approved by Intermatic Inc. could void the user’s authority to operate the
equipment.
equipment.
This device complies with part 15 of the FCC rules. Operation of this device is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference, including interference that may cause undesired operation.
(2) This device must accept any interference, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna or device.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
Faceplate Color Conversion
The faceplate color of this device can be converted to
match interior design requirements. Simply use one of
the included color plates (white, ivory, or light almond)
and proceed as follows (please note that the device must
be removed from the junction box to change the
faceplate, follow the installation instructions and
warnings).
1. Select the color of the faceplate you desire.
2. The faceplate has snaps on its sides. Using a small
screwdriver or thumbnail, gently remove the face plate
from the housing body.
3. Take the new faceplate and position it properly to the
housing body. Notice that the locking snaps will align in
only the proper direction. Line up the plastic snaps with
the slots in the housing body and snap into place.
4. The faceplate snaps in with an audible click. Ensure
that both snaps are secure. Replace the device in the
junction box following installation instructions.
The color conversion is complete.
The faceplate color of this device can be converted to
match interior design requirements. Simply use one of
the included color plates (white, ivory, or light almond)
and proceed as follows (please note that the device must
be removed from the junction box to change the
faceplate, follow the installation instructions and
warnings).
1. Select the color of the faceplate you desire.
2. The faceplate has snaps on its sides. Using a small
screwdriver or thumbnail, gently remove the face plate
from the housing body.
3. Take the new faceplate and position it properly to the
housing body. Notice that the locking snaps will align in
only the proper direction. Line up the plastic snaps with
the slots in the housing body and snap into place.
4. The faceplate snaps in with an audible click. Ensure
that both snaps are secure. Replace the device in the
junction box following installation instructions.
The color conversion is complete.
Providing a Brighter Solution™
158CA12472REF
WIRELESS CONTROLS
TM