Harman International Industries Inc MICROBT Manual Do Utilizador

1.  Read these instructions.
2.  Keep these instructions.
3.  Heed all warnings.
4.  Follow all instructions.
5.  Do not use this apparatus near water.
6.  Clean only with a dry cloth.
7.  Do not block any ventilation openings. 

Install this apparatus in accordance with the 

manufacturer’s instructions.

8.  Do not install this apparatus near any heat 

sources such as radiators, heat registers, 

stoves or other apparatus (including 

amplifiers) that produce heat.

9.  Do not defeat the safety purpose of 

the polarized or grounding-type plug. A 

polarized plug has two blades with one 

wider than the other. A grounding-type 

plug has two blades and a third grounding 

prong. The wide blade or the third prong 

is provided for your safety. If the provided 

plug does not fit into your outlet, consult an 

electrician for replacement of the obsolete 

outlet.

10.  Protect the power cord from being walked 

on or pinched, particularly at plugs, 

convenience receptacles and the point 

where they exit from the apparatus.

11.  Use only attachments/accessories 

specified by the manufacturer.

12.  Use only with the cart, stand, tripod, 

bracket or table specified by the 

manufacturer or sold with the 

apparatus. When a cart is used, 

use caution when moving the cart/

apparatus combination to avoid 

injury from tip-over.

13.  Unplug this apparatus during lightning 

storms or when unused for long periods 

of time.

14.  Refer all servicing to qualified service 

personnel. Servicing is required when the 

apparatus has been damaged in any way, 

such as when the power-supply cord or 

plug is damaged, liquid has been spilled 

or objects have fallen into the apparatus, 

or the apparatus has been exposed to rain 

or moisture, does not operate normally or 

has been dropped.

15.  Do not expose this apparatus to dripping 

or splashing, and ensure that no objects 

filled with liquids, such as vases, are 

placed on the apparatus.

16.  To disconnect this apparatus from the AC 

mains completely, disconnect the power-

supply cord plug from the AC receptacle.

17.  The mains plug of the power-supply cord 

shall remain readily operable.

18.  Do not expose batteries to excessive heat 

such as sunshine, fire or the like.

RISK OF ELECTRIC SHOCK. DO NOT OPEN.

THE LIGHTNING FLASH WITH AN 

ARROWHEAD SYMBOL, WITHIN AN 

EQUILATERAL TRIANGLE, IS INTENDED TO 

ALERT THE USER TO THE PRESENCE OF 

UNINSULATED “DANGEROUS VOLTAGE” 

WITHIN THE PRODUCT’S ENCLOSURE THAT 

MAY BE OF SUFFICIENT MAGNITUDE TO 

CONSTITUTE A RISK OF ELECTRIC SHOCK 

TO PERSONS.

THE EXCLAMATION POINT WITHIN AN 

EQUILATERAL TRIANGLE IS INTENDED TO 

ALERT THE USER TO THE PRESENCE OF 

IMPORTANT OPERATING AND MAINTENANCE 

(SERVICING) 

INSTRUCTIONS 

IN 

THE 

LITERATURE ACCOMPANYING THE PRODUCT.

WARNING:  TO REDUCE THE RISK OF FIRE 

OR ELECTRIC SHOCK, DO NOT EXPOSE THIS 

APPARATUS TO RAIN OR MOISTURE.

This device complies with part 15 of the FCC 

Rules. Operation is subject to the following two 

conditions: (1) This device may not cause harmful 

interference, and (2) this device must accept any 

interference received, including interference that 

may cause undesired operation.
This Class B digital apparatus complies with 

Canadian ICES-003.
Cet appareil numérique de la classe B est 

conforme à la norme NMB-003 du Canada. 
FEDERAL COMMUNICATION COMMISSION 

INTERFERENCE STATEMENT
This equipment has been tested and found 

to comply with the limits for a Class B digital 

device, pursuant to Part 15 of the FCC Rules. 

These limits are designed to provide reasonable 

protection against harmful interference in a 

residential installation. This equipment generates, 

uses and can radiate radio frequency energy 

and, if not installed and used in accordance with 

the instructions, may cause harmful interference 

to radio communications. However, there is no 

guarantee that interference will not occur in a 

particular installation. If this equipment does 

cause harmful interference to radio or television 

reception, which can be determined by turning 

the equipment off and on, the user is encouraged 

to try to correct the interference by one or more of 

the following measures:
•  Reorient or relocate the receiving antenna.
•  Increase the separation between the equipment 

and receiver.

•  Connect  the  equipment  into  an  outlet  on  a 

circuit different from that to which the receiver 

is connected.

•  Consult the dealer or an experienced radio/TV 

technician for help.

Caution: Changes or modifications not expressly 

approved by HARMAN could void the user’s 

authority to operate the equipment.
FOR PRODUCTS THAT TRANSMIT RF  

ENERGY:
FCC AND IC INFORMATION FOR USERS
This device complies with Part 15 of the FCC 

rules and Industry Canada license-exempt RSS 

210. Operation is subject to the following two 

conditions: (1) This device may not cause harmful 

interference; and (2) this device must accept any 

interference received, including interference that 

may cause undesired operation. 
FCC/IC Radiation Exposure Statement
This equipment complies with FCC/IC RSS-

102 radiation exposure limits set forth for an 

uncontrolled environment. This equipment should 

be installed and operated with minimum distance 

20cm between the radiator & your body.

GROUNDING
If an outside antenna or cable system is connected 

to this product, be certain that it is grounded so as 

to provide some protection against voltage surges 

and static charges. Section 810 of the National 

Electrical Code (NEC), ANSI/NFPA No. 70-1984, 

provides information with respect to proper 

grounding of the mast and supporting structure, 

grounding of the lead-in wire to an antenna 

discharge unit, size of grounding conductors, 

location of antenna discharge unit, connection 

to grounding electrodes and requirements of the 

grounding electrode. 
NOTE TO CATV SYSTEM INSTALLER:
This reminder is provided to call the CATV (cable 

TV)  system  installer’s  attention  to  article  820-40 

of the NEC, which provides guidelines for proper 

grounding  and,  in  particular,  specifies  that  the 

cable ground shall be connected to the grounding 

system of the building, as close to the point of 

cable entry as possible.

IMPORTANT SAFETY INSTRUCTIONS