Enlighted Inc. RS-2BSU-2B Manual Do Utilizador
Enlighted Ruggedized
Sensor Installation
Instructions
Shipped Components
The following components are shipped with the Enlighted Ruggedized Sensor Unit:
•
Enlighted Ruggedized Sensor Unit
•
Ruggedized Nut
Tools You May Need
•
Whole Saw
•
11/16 Drill Bit
Enlighted Ruggedized Sensor Installation Instructions Document # 94-00415-01
Installing the Enlighted Ruggedized Sensor
This section provides step-by-step instructions on how to install the
Enlighted Ruggedized Sensor.
Before You Begin
Before you begin the installation of the Enlighted Ruggedized
Sensor, be sure to review the following cautionary steps to ensure a
safe installation:
safe installation:
1. Disconnect all power before installation or service.
2. Installation and maintenance must be performed by qualified
personnel.
3. Installations and maintenance must be performed in
accordance with state, local, and national electrical codes and
requirements.
requirements.
To Install the Enlighted Ruggedized Sensor
To install the Enlighted Ruggedized Sensor Unit, perform the
following steps:
Step
Action
1.
Turn off all power to the light fixture by switching off the circuit breaker.
2.
Ensure the RJ12 data cable is installed and connected to the Enlighted
Control Unit mounted in the ballast cavity of the fixture or mounted in a
ULapproved enclosure. (See Figure 1)
Control Unit mounted in the ballast cavity of the fixture or mounted in a
ULapproved enclosure. (See Figure 1)
Ensure the Enlighted Ruggedized Sensor is mounted within a few feet of
3. the lighting fixture and over the service area of outdoor light.
4.
Connect the Enlighted Ruggedized Sensor to the Ruggedized Screw.
Note: You can extend the Enlighted Ruggedized Sensor away from the
fixture. To do this: course a threaded 1/2 inch threaded fitting. This will
create a 90 degree elbow to knockout or 1/2 inch drilled out hole on
fixture.
Note: You can extend the Enlighted Ruggedized Sensor away from the
fixture. To do this: course a threaded 1/2 inch threaded fitting. This will
create a 90 degree elbow to knockout or 1/2 inch drilled out hole on
fixture.
5.
Insert Enlighted Ruggedized Sensor into hole.
6.
Use Ruggedized Sensor Nut to attach sensor.
Connect linear 6-pin coupler to the Enlighted Ruggedized Sensor. (See 7.
Figure 2)
Figure 1: Fixture Combo
Figure 2: Wiring Diagram
Troubleshooting the Enlighted
Ruggedized Sensor
Problem
Solution
There are no green flashing LED lights.
Verify Enlighted Ruggedized Sensor
cable is plugged into the Enlighted
Ruggedized Sensor unit.
cable is plugged into the Enlighted
Ruggedized Sensor unit.
Red blinking LED.
Possible solutions:
•
Replace Enlighted Ruggedized
Sensor cable.
Sensor cable.
•
Replace Enlighted Control Unit.
January, 2014
Technical Support
For questions regarding the installation or operation of this product, contact
Enlighted Technical Support: support@enlightedinc.com.
FCC and Industry Canada Compliance
Information
USA
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
•
this device may not cause harmful interference, AND
•
this device must accept any interference received, including interference
that may cause undesired operation.
that may cause undesired operation.
Changes or modifications not expressly approved by Enlighted Inc. could void
the user's authority to operate the equipment.
Canada
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions:
•
this device may not cause harmful interference, AND
•
this device must accept any interference received, including interference
thatmay cause undesired operation.
thatmay cause undesired operation.
Changes or modifications not expressly approved by Enlighted Inc. could void
the user's authority to operate the equipment.