Futaba Corporation PK-AM-75 Manual Do Utilizador
ADJUSTABILITY:
•
Master:
Throttle, steering, channel 3.
•
Slave:
Throttle, steering, channel 3.
•
A and B adjustments [Up/forward/left and down/brake/right (for ch3/throttle/steering respectively)]: -100% (move
exact opposite of master) to 0 (no movement of slave) to +100% (move exactly same as master). Default: 50%.
Adjustable while in use by selecting a dial/trim for programmable mix adjustments A and B in
exact opposite of master) to 0 (no movement of slave) to +100% (move exactly same as master). Default: 50%.
Adjustable while in use by selecting a dial/trim for programmable mix adjustments A and B in
FUNC-DIAL, pp. 34-35.
•
Offset:
-100% to 0 to +100%. Default: 0%.
•
Master mixed mode: Off, mixed. Default: off.
•
Trim:
Off, On. Default: Off.
•
Switch:
An on/off switch may be assigned for each mix in
FUNC-SW (see pp. 34-35).
INTERACTION: EPA affects total travel available to both servos. Master mixed mode “mixed” means that all other
functions affecting the primary channel also affect the secondary channel.
functions affecting the primary channel also affect the secondary channel.
DESIRED END RESULT: Varies based upon user setup.
CAUTION: Be sure to test all mixes at every step to ensure no unexpected difficulties occur.
41
GOAL:
Set up a programmable mix from steering
to lights so that headlights turn with
steering wheel, while using
to lights so that headlights turn with
steering wheel, while using
LV3. (If using
LV1 or LV2, first select level LV3, see p. 12.)
STEPS:
Select programmable mix 1.
Make mix active.
Set master channel as steering.
Set slave channel as ch 3.
Set left and right travel as 100%.
Set master mixed mode to mixed so other
mixes affecting throttle position also
affect headlight angle.
Set trim on so movement of steering trim
also moves headlights.
Close function and menu.
mixes affecting throttle position also
affect headlight angle.
Set trim on so movement of steering trim
also moves headlights.
Close function and menu.
INPUTS:
to
ACT.
(already steering)
to
CH3.
to
100%. to
100%.
to
MIX.
to
ON.
GOAL:
Use mixes to increase steering travel slightly
when dual rate and EPA are not enough,
while using
when dual rate and EPA are not enough,
while using
LV3. [Note that anything more
than 10% (or less if subtrim is >0) will not
move the servo any further, as the servo’s
maximum mechanical travel is exceeded. Be
sure to check actual travels, including sub
trims, by testing servo operation.] (If using
LV1 or LV2, first select level LV3, see p. 12.)
move the servo any further, as the servo’s
maximum mechanical travel is exceeded. Be
sure to check actual travels, including sub
trims, by testing servo operation.] (If using
LV1 or LV2, first select level LV3, see p. 12.)
Where Next:
STEPS:
Select programmable mix 1.
Make mix active.
Set master channel as steering.
Set slave channel as steering.
Set left and right travel as 10%.
Leave offset at 0 and trim off.
Set master mixed mode to mixed so other
mixes affecting steering also. See the
increase.
Close function and menu.
Set master mixed mode to mixed so other
mixes affecting steering also. See the
increase.
Close function and menu.
INPUTS:
to
ACT.
(already steering)
to
ST.
to
10%.
to
10%.
to
MIX.
Programmable mix to set up differential steering (similar to the brake mixing program
but for 4-wheel steering or for 2-wheel steering using 2 servos and creating adjustable
acumen): see www.futabarc.com\faq\faq-3pk.html
Adjust steering EPA (
but for 4-wheel steering or for 2-wheel steering using 2 servos and creating adjustable
acumen): see www.futabarc.com\faq\faq-3pk.html
Adjust steering EPA (
ST-EPA): See p. 18.
Adjust steering dual rate (
ST-DR): See p. 38.
Adjust steering subtrim (
SUB-TRIM): See p. 22.