Futaba Corporation R6308SBT-24G Manual Do Utilizador

 Receiver

This device, trade name Futaba Corporation of America, model number 

R6308SBT, complies with part15 of the FCC Rules. Operation is subject to the 

following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference 

that may cause undesired operation.

(3) This module meets the requirements for a mobile device that may be used 

at separation distances of more than 20cm from human body.

To meet the RF exposure requirements of the FCC this device shall not be co-

located with another transmitting device.

The responsible party of this device compliance is:

Futaba Service Center

3002 N Apollo Drive Suite 1, Champaign, IL 61822 U.S.A.

TEL (217)398-8970 or E-mail: support@futaba-rc.com (Support)

FASST-2.4GHz system(7CH/8CH/10CH/Multi-ch mode)/S.BUS2 and 

S.BUS port and 8 channels for conventional system receiver
• Dual antenna diversity

• Size: 0.98 x 1.86 x 0.56 in. (24.9 x 47.3 x 14.3 mm)

• Weight: 0.38 oz. (10.9g)

• Power requirement: 3.7V to 7.4V(Voltage range: 3.5 to 8.4V)

•  Battery  F/S  Voltage:  3.8V 

• Extra Voltage port: 0 ～ 70V DC

* Be sure that when using ESCs regulated output the capacity of the ESC must 

meet your usage condition.

Thank you for purchasing a Futaba R6308SBT FASST-2.4GHz compatible receiver. The R6308SBT receiver features bi-directional communication 

with a telemetry receiver unit (option) using the S.Bus2 port.  Using the S.Bus2 port an impressive array of telemetry sensors may be utilized.  It also 

includes both standard PWM output ports and S.Bus output ports. This receiver distinguishes automatically FASST-2.4-GHz system 7ch or Multi-

ch/10ch / 8ch mode at the time of link operation with a transmitter. And high speed mode can be chosen.

Green

Red

Status

No signal reception

Receiving signals

ID of a signal is disagreement

Unrecoverable error (EEPROM, etc.)

Please refer the table below for LED status vs 

receiver's condition.

1M23N17459

S.BUS2

port

S.BUS port

(8/SB）

(S.BUS2）

S.BUS Servo

S.BUS Gyro

HUB

HUB

HUB

HUB

Extra Voltage

Port

Link/Mode switch

Antenna

LED

Servo for conventional

system

Channel1 output
Channel8 output

Temperature

Sensor

RPM

Sensor

Voltage

Sensor

Voltage

Sensor

Altitude

Sensor

Altitude

Sensor

S.BUS2 Tool

Battery to 7/B

＋

−

It connects with the 

battery for power, etc.

cable of an option is 

used. The voltage of 

the battery can be 

displayed with a 

transmitter. 

When using S.BUS, it is 

necessary to change CH 

mode into B or D.

HUB

 

Changes or modification not expressly approved by the 

party responsible for compliance could void the user’s 
authority to operate the equipment.

 

The R6308SBT receiver should be protected from vibra-

tion by foam rubber, Velcro or similar mounting meth-

ods.  Protect from moisture.

 

Keep away from conductive materials to avoid short cir-

cuits.

 

Don't connect to Extra Voltage before turning on a receiv-

er.

 

Do not cut or bundle the receiver antenna wire.  
     

 

Do not bend the coaxial cable. It causes damage.

 

The antennas must be mounted in such a way to assure 

they are strain relieved.                                                                                

 

Keep the antenna as far away from the motor, ESC and 

other noise sources as you possibly can.

 

Be sure that the two antennas are placed at 90 degrees to 

each other.

• The  R6308SBT  has  two  antennas.    In  order  to  maximize  signal

reception and promote safe modeling Futaba has adopted a diversity 

antenna system.  This allows the receiver to obtain RF signals on both 

antennas and fly problem-free.

 

You must leave 30mm at the tip of the antenna fully ex-

posed. The exposed antenna should be secured so that it 

cannot move around or back inside of your aircraft.