Bright Ideas Inc BLUESYNCMC Manual Do Utilizador

 

a

c

Thank you for purchasing the 

GOgroove™  BlueSync™ MC

move freely with your Bluetooth enabled device up to 30 feet! The GOgroove 
BlueSync MC also supports non-Bluetooth audio devices with the included 
3.5mm cable and AUX line-in port. The BlueSync MC’s stylish, modern design 
and full-range sound complements and equips any room with stunning 
Bluetooth audio.

a- BlueSync MC Speaker 
b- AC plug
c- 3.5mm audio cable

1- Play/Pause button
2- Volume +/- buttons
3- Bluetooth pairing button
4- Power LED indicator

6- AUX line-in port
7- DC in port

Connect the BlueSync MC to Power:

Connect the (b) AC plug into a wall outlet and plug the small end into the (7) DC in port. 
Find the 

 on the rear of the speaker and switch it to the ON position. 

The (4) Power LED indicator

your device’s user manual for further information.  

a. Make sure that your mobile device is within at least 3 feet of the receiver when 

trying to pair and that the BlueSync MC is powered on.

b. Enter pairing mode on the BlueSync MC by pressing and holding the (3) Bluetooth 

pairing button for 3 seconds until the (4) Power LED indicator
you hear 2 short tones.

c. Access the Bluetooth settings in your mobile device and select SEARCH/SCAN FOR 

DEVICES. Your mobile device will begin to search for a Bluetooth Signal. 

d. You will see the name “BlueSync MC”appear in the device list. Select it to pair, and 

if a password or PIN is needed enter the numbers “0000”. 

    ***You may have to then select BlueSync MC and press “CONNECT”. 
e. After a successful connection has been made, you will hear a short tone and the 

a. Toggling allows you to switch between devices that have been paired with the 

BlueSync MC.

b. To switch devices, press the (3) Bluetooth pairing button once. Allow 3 seconds 

after pressing the (3) Bluetooth pairing button. Press up to 8 times to toggle 
through the paired memory. If your device does not connect after toggling, please 
refer to the pairing instructions.

c. After a successful connection has been made you will hear a short tone.

b

1

3

2

4

6

5

7

a. Please make sure the BlueSync MC is in PAIRING MODE and that the (4) Power 

BlueSync MC and start from 

the beginning of “Pairing your mobile Bluetooth device to the BlueSync MC” 
instructions above.

b. Please make sure the (c) 3.5mm audio cable is disconnected from the (6) AUX line-in 

port. Once disconnected, start from the beginning of “Pairing your mobile Bluetooth 
device to the BlueSync MC” instructions above.

a. Please make sure that your Bluetooth mobile device supports A2DP (audio/music) 

connection.

b. Please make sure your device is paired to the BlueSync MC. To switch to another 

Bluetooth audio device refer to the “Toggling between paired devices” instructions above.

a. Please make sure that the 

 is in the ON position and that the (4) 

Power LED indicator is illuminated.

b. Please make sure that the volume on your mobile device and the BlueSync MC are 

loud enough.

c. Please make sure that your mobile Bluetooth device is within 30 feet of the 

BlueSync MC
and on the paired device.

a. The BlueSync MC remembers up to 8 paired devices. When reconnecting you will 

not have to go through the initial pairing set up.

b. To reconnect, make sure that your mobile device is within at least 3 feet of 

the receiver and press the (3) Bluetooth pairing button to toggle through the 
remembered devices.  Allow 3 seconds after pressing the (3) Bluetooth pairing 
button each time.

c. If your device does not automatically reconnect by toggling, access the Bluetooth 

settings in your mobile device and select “BlueSync MC”. 

d. After a successful connection has been made, you will hear a short tone. If your 

device does not connect after toggling, please refer to the “Pairing your mobile 
Bluetooth device to the BlueSync MC” instructions above.

1- Make sure that your Bluetooth A2DP (audio/music) mobile device is paired with the 

BlueSync MC.

2- Simply begin playing music on your mobile device and you should hear the music 

play through the BlueSync MC. If the music is low, increase the volume on the 
BlueSync MC

3- You can control the volume and playback directly from the BlueSync MC using the 

(1) Play/Pause button and (2) Volume +/- button.

4- If you would like to connect a device which does not have Bluetooth capability, 

you may use the (6) AUX line-in port on the BlueSync MC. Just use the included (C) 
3.5mm audio cable. Connect one end to the headphone jack of your music playing 
device, and the other end into the (6) AUX line-in port on the rear of the BlueSync 
MC. Once connected, begin playing music on your mobile device and you should 
hear the music play through the BlueSync MC.

Operating Instructions continued

Speaker: (3wx2) 6w RMS; 12w Peak

Operating distance: 30 feet
Power: AC110v
Input: Standard 3.5mm audio plug (cable included)
Dimensions: 11 x 4 x 3.75 inches
Weight: 2.5 lbs

- Please only use this product in the manner described in this manual
- Please keep out of the reach of children
- Do not expose the unit to dust, water, or extreme temperatures
- Do not attempt to disassemble the product

©

2012 ACCESSORY POWER

All trademarks and brand names are the property of their owners.

FCC NOTE
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this 
device may not cause harmful interference, and (2) this device must accept any interference received, including 
interference that may cause undesired operation.
The antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from 
all persons and must not be co-located or operated in conjunction with any other antenna or transmitter.